SIOUX 2A1110 Instrucciones Y Lista De Piezas

INSTRUCTIONS & PARTS LIST FOR NO. 2 1/2 SERIES 45° & 90° ANGLE DRILLS
Read and understand "Safety Instructions For Air Tools" and these instructions before
Tools left connected to the air supply while making adjustments, changing accessories, or doing any
Always remove tool from air supply and activate trigger to bleed air line before making any adjust-
ments, changing accessories, or doing any maintenance or service on tool.
AIR SUPPLY
The efficiency of the tool is dependent on the proper supply of clean dry air at 90 psig (6.2 bar). The use of a line filter,
pressure regulator, and lubricator will insure maximum output and life of tools.
HOSE AND HOSE CONNECTIONS
Supply hose should be not less than 3/8" (10 mm) I.D. Extension hoses should be at least 1/2" (13 mm) I.D. Use couplings
and fittings with at least 3/8" (10 mm) I.D.
LUBRICATION
Use SIOUX 288 air motor oil. An airline lubricator, set to deliver 2 to 4 drops per minute, is recommended. If a lubricator is
not used, add .04 oz. (1.2 cc)(12 to 15 drops) of SIOUX No. 288 air motor oil into the air inlet daily.
Lubricate the planetary gear assemblies with 1/4 oz (7 gm) of SIOUX No. 298A grease after every 100 hours of operation.
Lubricate the angle head with 0.01 oz (0.3 gm) of SIOUX 1198 grease after every 8 hours of operation.
GENERAL OPERATION
Start the tool by depressing the lever. Motor speed can be adjusted with the slotted screw at the rear of the housing oppo-
site the lever.
We, Sioux Tools Inc., 250 Snap-on Drive, P.O. Box 1596, Murphy, NC, 28906, USA, declare under our sole responsibility that the products
to which this declaration relates are in conformity with the following standard or standards or other normative document or documents:
June 1, 2003
Murphy, North Carolina, USA
Date and place of issues
operating this tool.
maintenance or service on tool can start unexpectedly.
Tools starting unexpectedly can cause injury.
SOUND AND VIBRATION READINGS
Catalog No. Sound Pressure dBA
2A1110 82.1
2A1310 82.1
2A1410 82.1
2A1510 82.1
2A1610 82.1
2AY1310 82.1
2AY1400 82.1
2AY1410 82.1
2AY1510 82.1
2AY1610 82.1
*prt PN8NTC1
DECLARATION OF CONFORMITY
2A1110, 2A1310, 2A1410, 2A1510, 2A1610, 2AY1310, 2AY1400, 2AY1410,
2AY1510, 2AY1610 including 45, AH suffixes
EN 792 (draft), EN 292 Parts 1&2, ISO 8662, Pneurop PN8NTC1
following the provisions of
89/392/EEC as amended by 91/368/EEC & 93/44/EC Directives.
Gerald E. Seebeck
Sioux Tools Inc.
Name and position of issuer
Sound Power dBA Vibration m/s
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
94.8 Less than 2.5
*prt PN8NTC1 *per ISO8662
President
1
Form ZCE468A
Date 2003June20/D
Page 1 of 12
2
Signature of issuer
Printed In U.S.A.