AEB COL4 Manual Del Usuario página 32

TESTING PROCEDURES
Connect the product to testing wiring no. 1.
Check that any tester switch is set to OFF, that the knobs are all rotated in counter-clockwise direction
and that the rotating INDICATOR is set to RIS.
Once the product has been connected, set the commutator to GAS.
Set the switch +12 V Batt. to ON.
Set the switch +12 V Sc to ON. The YELLOW LED of the commutator and the GREEN LED OUT GAS of
the tester will turn on for a priming period given by the trimmer position located on the rear side of
the commutator and the will turn off.
The GREEN LED and the RED LED for RESERVE on the commutator will remain on to indicated that the
commutator is set to GAS.
Set the switch RPM to ON. The GREEN LED OUT GAS on the tester and the YELLOW LED on the
commutator will turn on.
By setting the INDICATOR switch from RIS to R and vice versa, you can test the correct operation of
the LEDs RESERVE.
By setting the switch on the commutator to the central position, the GREEN LED OUT GAS on the
tester will turn off and all the LEDs on the commutator will turn off.
By setting the switch of the commutator to BENZINA (GASOLINE), the RED LED on the commutator
and the RED LED OUT BENZ. on the tester will turn on.
By setting the switch of the commutator to the central position, you go back to the OFF condition.
By setting the switch of the product to GAS, the YELLOW LED GAS, the GREEN LED and the RED LED
RESERVE on the product will turn on, while the LED OUT GAS on the tester will turn on.
By setting the switch RPM to OFF, after a slight delay the LED OUT GAS of the tester and the YELLOW
LED on the product turn off.
Set the switches to OFF.
Connect the product to wiring no. 6 by connecting together the wires having the same colour.
The white wire must not be connected.
Check that the tester switches are set to OFF and that the knobs are all rotated in counter-clockwise
direction.
Once the product has been connected, set the switch +12 V Batt. to ON.
Set the switch +12 V Sc to ON.
By setting the GAS/BENZINA (GASOLINE) switch on the product to GASOLINE, the RED LED GASOLINE
on the product and the RED LED OUT BENZ. on the tester turn on.
By setting the GAS/BENZINA (GASOLINE) switch on the product to GAS, the GREEN LED GAS on the
product and the GREEN LED OUT GAS on the tester turn on.
By setting the GAS/GASOLINE switch on the product to the central position, all the LEDs are off.
By pressing the priming button on the product, the YELLOW LED CPU/CICC. on the tester will turn on.
Switches to OFF.
Connect the product to wiring no. 6 by connecting together the wires having the same colour.
Check that any tester switch is set to OFF, that the knobs are all rotated in counter-clockwise direction
and that the rotating INDICATOR is set to RIS.
Once the product has been connected, set the switch +12 V Batt. to ON.
Set the switch +12 V Sc to ON. The RED LED RESERVE on the product will turn on.
By setting the GAS/BENZINA (GASOLINE) switch on the product to GASOLINE, the YELLOW LED
GASOLINE on the product and the RED LED OUT BENZ. on the tester turn on.
By setting the GAS/BENZINA (GASOLINE) switch on the product to GAS, the GREEN LED GAS on the
product and the GREEN LED OUT GAS on the tester turn on.
By setting the GAS/GASOLINE switch on the product to the central position, all the LEDs are off apart
from the red LED.
By pressing the priming button on the product, the YELLOW LED CPU/CICC. on the tester will turn on.
By setting the INDICATOR knob from RIS to R and vice versa, you can test the correct operation of the
LED RESERVE (RIS = led ON; R = led OFF).
32 - 64
CODE AEB652i
CODE AEB656
CODE AEB658
IsCOL4 Rev. 250902-0