Stanley Fatmax FMHT1-77416 Manual De Instrucciones página 10

4. Push the battery compartment cover closed until it snaps in
GB
place (Figure
B
5.
Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
6.
On the keypad, make sure
flashing (> 5%). If
battery level is below 5%.
• The laser may continue to operate for a short time while
the battery power continues to drain, but the laser lines
and dots will quickly dim.
• After fresh batteries are installed and the laser is turned
ON again, the laser lines and dots will return to full
brightness.
7.
When the laser is not in use, slide the Power/Transport
Lock switch to the LEFT to the Locked/OFF position
(Figure #1a) to save battery power.
A
Using the Mounting Block
On the bottom of the laser is a moveable block (Figure
• To use the magnets on the front of the laser (Figure
mount the laser against the side of a steel beam, do not
extend the moveable block (Figure
down dot to be aligned with the edge of the steel beam.
• To mount the laser over a point on the floor (using a multi-
function bracket or a tripod), pull out the moveable block until
it clicks in place (Figure
dot to display through the 5/8-11 mounting hole and the laser
to be rotated over the 5/8-11 mounting hole without moving
the vertical position of the laser.
Turning the Laser On
1. Place the laser on a smooth, flat, level surface, with the
laser facing straight ahead toward the opposing wall
(0º position).
2. Slide the Power/Transport Lock switch to the right to the
Unlocked/ON position (Figure
3.
Press (Figure
line, a second time to display a down dot, and a third time
to display a horizontal line and a down dot.
10
#3).
#1b).
A
#3) is not
(Figure
A
is flashing, this means that the
#1). This will allow the
D
#2). This will allow the laser down
D
#1b).
A
#6) once to display a horizontal laser
A
4. Check the laser beams. The laser is designed to self-level.
• If the laser is tilted so much that it cannot self-level
(> 4°), the laser beams will continually flash twice and
(Figure
• If the laser beams flash, the laser is not level (or plumb)
and should NOT BE USED for determining or marking
level or plumb. Try repositioning the laser on a level
surface.
5. Press (Figure
line from the front of the laser, a second time to display
a vertical laser line from the side of the laser, and a third
time to display both vertical lines.
6. Press (Figure
illuminate and the laser beams will appear lighter, since
they are flashing at a very rapid rate. You will only use
Pulse mode with a detector to display the laser beams long
range.
7. If ANY of the following statements are TRUE, continue with
the instructions for Checking Laser Accuracy BEFORE
USING THE LASER for a project.
).
D
• This is the first time you are using the laser (in case
#2) to
A
the laser was exposed to extreme temperatures).
• The laser has not been checked for accuracy in
a while.
• The laser may have been dropped.
Checking Laser Accuracy
The laser tools are sealed and calibrated at the factory. It
is recommended that you perform an accuracy check prior
to using the laser for the first time (in case the laser was
exposed to extreme temperatures) and then regularly to
ensure the accuracy of your work. When performing any of
the accuracy checks listed in this manual, follow these
guidelines:
• Use the largest area/distance possible, closest to the
operating distance. The greater the area/distance, the
easier to measure the accuracy of the laser.
• Place the laser on a smooth, flat, stable surface that is
level in both directions.
• Mark the center of the laser beam.
#4) will flash constantly on the keypad.
A
#5) once to display a vertical laser
A
#7) to test the Pulse mode.
A
will