Allmatic PROXIMA W Manual De Instrucciones página 4

4.4 Deleting a transmitter from the memory of a control unit
PRESS the "e"
a
hidden key
a
1
e
PRESS the "e"
hidden key + "a"
a
a
1
e
Warning: Do not carry on this procedure if more than one control unit is working, because the opening of memory would take
place for all devices where a channel has been memorized. Cut power supply for all control units not involved in the operation.
4.5 Total memory reset of a control unit
1) Cut power supply of the control unit
2) Keeping the LEARN button pressed, give power back to the control unit. The unit emits a sequence of continuous beeps (through the buzzer, if
present on the card). When signal stops, reset procedure is completed and it is possible to release the LEARN button.
After this operation the control unit will emit a sequence of beeps (through the buzzer, if present on the card) first fast and then slow, to
indicate the empty memory. The control unit will automatically enter the learning mode, waiting for a signal from a transmitter.
5. Advanced configuration: setting of jumpers (if present)
Transmitter Pushbuttons
Pressing shortly the open / close buttons activates the opening / closing for a short movement (snap). This allows the setting of
Venetian blinds.
Pressing for a longer time leads to a complete opening/closing of the shutter. In order to stop the automation in the required position,
press the STOP button or the button operating the movement in the opposite direction.
Wall pushbuttons connected by cable:
J1 J2
The operation is analogous to that for the transmitter pushbuttons concerning the snap progress , useful for Venetian blinds. An
extended pressing of the OPEN button activates opening. A further pressing of the same button stops the opening. Pressing the
CLOSE button activates the inversion of the run direction (closing). Operation is specular for the other button.
Receiving of the transmitters
Disabled
Wall pushbuttons connected by cable:
Dead man operation, meaning that the roller shutter goes up/down while the buttons are kept pressed. Releasing them the roller
J1 J2
shutter stops.
Transmitter Pushbuttons
Pressing the open/close button the roller shutter opens or closes completely. A second pressing of the same button does not stop the
movement. In order to stop it press the STOP button or the button for the movement in the opposite direction.
Wall pushbuttons connected by cable:
J1 J2
Operation is analogous to transmitter pushbuttons.
Transmitter Pushbuttons
The operation is step by step with 1 button: the first pressing of the OPEN button starts the opening, the second pressing stops the
roller shutter, the third closes.
Please Note: In this operation mode the control unit is controlled by a single transmitter button, precisely the "a" button. The "b"
button will not have any effect and the "c" button keeps the STOP function.
Wall pushbuttons connected by cable:
The operation is step by step with 2 buttons: the first pressing of the OPEN button starts the opening, the second pressing stops it
J1 J2
and the third restarts it. The same happens for closing, by means of the related button.
GUARANTEE - In compliance with legislation, the manufacturer's guarantee is valid from the date stamped on the product and is restricted to the repair
or free replacement of the parts accepted by the manufacturer as being defective due to poor quality materials or manufacturing defects. The guarantee
does not cover damage or defects caused by external agents, faulty maintenance, overloading, natural wear and tear, choice of incorrect product,
assembly errors, or any other cause not imputable to the manufacturer. Products that have been misused will not be guaranteed or repaired.
Printed specifications are only indicative. The manufacturer does not accept any responsibility for range reductions or malfunctions caused by
environmental interference. The manufacturer's responsibility for damage caused to persons resulting from accidents of any nature caused by our
defective products, are only those responsibilities that come under Italian law.
6-1622117 Rev. 2 24/10/2014
DELETING a transmitter of B.RO series:
b
1) Press the "e" hidden key in the transmitter. The control unit emits a sequence of beeps (through the buzzer, if
b
1 present on the card) or flashings. This operation is equivalent to pressing the LEARN button, but without need of
physically opening the control unit.
2) Press at the same time for a few seconds the hidden key and a key of the transmitter that must be deleted (e.g.
"e" and "a" or "e" and "a1"). Deleting is signaled by means of 4 long beeps (through the buzzer, if present on the
card). After this, the control unit goes back to the normal operation mode.
b
DELETING a transmitter of CLARUS series:
b
1
In order to delete a single channel or the complete transmitter, it is necessary to enter the internal menu of the
transmitter itself. To carry on this operation, please refer to the user's guide of the transmitter.
Open Jumper
ITA
LEGENDA
Closed Jumper
ENG FRA ESP DEU POR
2/2