Toro 110-4997 Instrucciones De Instalación
  1. Manuales
  2. Marcas
  3. Toro Manuales
  4. Accesorios para Cortacéspedes
  5. 110-4997
  6. Instrucciones de instalación
Toro 110-4997 Instrucciones De Instalación

Toro 110-4997 Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
7
8
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Kawasaki Engine Conversion Kit
For Suzuki-Powered heavy-Duty Lawn Mowers
Model No. 110-4997
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
1
Removing the Old Engine
No Parts Required
Procedure
Important: Save all fasteners that you removed for
reuse unless otherwise noted.
1. Drain the fuel from the fuel tank.
2. Remove the old belt cover and discard it.
3. Remove and discard the throttle control cable.
4. Remove and discard the old fuel hose, fuel filter,
and clamp.
© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
Belt cover (74-1770)
Engine (106-0845)
Decal (110-0520)
Screws (95-1727)
Retainer spacer (103-3795)
Tank bracket (106-0908-03)
Fuel tank cap (93-7198)
Screws (104-2628)
Fuel hose (109-0296)
Fuel filter (71-9280)
Clamp (2412-98)
Fuel hose (109-0650)
Cable tie (3290-378)
Blade bolt (3212-4)
BBC Spacer (107-4058)
Spring washers (1-603610)
Throttle control (114-3488)
Register at www.Toro.com.
Qty.
–
Remove the old engine.
1
1
1
4
1
1
1
3
1
Install the new engine.
1
4
1
4
1
1
2
1
5. Remove the blade and the BBC assembly.
6. Remove the belt from the driver pulley; inspect the
belt for wear and replace it if necessary.
7. Remove the engine mounting bolts.
8. Remove the old engine from the mower housing.
9. Remove the fuel tank from the tank base and retain
it for reuse.
10. Replace the fuel tank cap with a new cap provided in
the kit; discard the old fuel tank cap.
11. Remove and discard the discharge tunnel door.
12. Clean the mower housing and check it for damage
and wear.
Form No. 3355-538 Rev B
Installation Instructions
Use
Original Instructions (EN)
Printed in the USA
All Rights Reserved
loading

Manuales relacionados para Toro 110-4997

Resumen de contenidos para Toro 110-4997

  • Página 1 Form No. 3355-538 Rev B Kawasaki Engine Conversion Kit For Suzuki-Powered heavy-Duty Lawn Mowers Model No. 110-4997 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Remove the old engine.
  • Página 2 Figure 1 1. Engine 7. Tank retainer 2. Mower deck 8. Fuel hose, fuel filter, and clamps 3. Belt cover 9. Engine mounting bolt (4) 4. Fuel tank cap 10. Spacer 5. Throttle control 11. Spring washer 6. Discharge door 12.
  • Página 3 Note: The short hose attaches to the fuel tank. 7. Install and adjust the new throttle control cable. 8. Replace the belt cover. Installing the New Engine Parts needed for this procedure: Belt cover (74-1770) Engine (106-0845) Decal (110-0520) Screws (95-1727) Retainer spacer (103-3795) Tank bracket (106-0908-03) Fuel tank cap (93-7198)

  • Página 5: Instalación

    Form No. 3355-538 Rev B Kit de conversión a motores Kawasaki Cortacéspedes para servicio pesado con motor Suzuki Nº de modelo 110-4997 Instrucciones de instalación Instalación Piezas sueltas Utilice la tabla siguiente para verificar que no falta ninguna pieza. Procedimiento Descripción...
  • Página 6 Figura 1 1. Motor 7. Placa de sujeción del depósito 2. Plataforma de corte 8. Tubo de combustible, filtro de combustible, y abrazaderas 3. Cubierta de la correa 9. Perno de montaje del motor (4) 4. Tapón del depósito de combustible 10.

  • Página 7: Instalación Del Motor Nuevo

    Nota: Apriete el perno de la cuchilla a 28,2–36,2 Nm. 6. Conecte el tubo de combustible, el filtro de combustible, y la abrazadera nuevos al motor y al Instalación del motor nuevo depósito de combustible. Nota: El tubo corto se conecta al depósito de Piezas necesarias en este paso: combustible.