Technical Data; Drill Safety Warnings; Screwdriver Safety Warnings - BTI A18 BS-2 Manual Original

TECHNICAL DATA

Code ...................................................................................................
Drilling capacity in steel ......................................................................
Drilling capacity in wood .....................................................................
Wood screws (without pre-drilling) .....................................................
No-load speed 1st gear ......................................................................
No-load speed 2nd gear .....................................................................
Torque with battery (1.5/2.0 Ah)..........................................................
Torque with battery (3.0/4.0/5.0 Ah)....................................................
Battery voltage....................................................................................
Drill chuck range .................................................................................
Weight according EPTA-Procedure 01/2003 (1.5/2.0 Ah) ..................
Weight according EPTA-Procedure 01/2003 (3.0/4.0/5.0 Ah) ............
Weight according EPTA-Procedure 01/2003 (9.0 Ah) ........................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ...................................
Sound power level (Uncertainty K=3dB(A)) ........................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a
h
Percussion drilling into concrete......................................................
Uncertainty K= .................................................................................
Drilling into metal .............................................................................
Uncertainty K= .................................................................................
Screwing..........................................................................................
Uncertainty K= .................................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or
poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the
job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm,
organisation of work patterns.
WARNING! Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a „live" wire may make exposed metal parts of the
power tool „live" and could give the operator an electric shock.

SCREWDRIVER SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when performing an
operation where the fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the
machine. The use of protective clothing is recommended, such as dust mask,
protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the
device on again while the insertion tool is stalled, as doing so could trigger a
sudden recoil with a high reactive force. Determine why the insertion tool stalled
and rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
ENGLISH
445 273 - BTI-A18BS-2.indd 18 445 273 - BTI-A18BS-2.indd 18
CORDLESS DRILL DRIVER
A18 BS-2 02 00001- 99999
.............................. 13 mm
.............................. 38 mm
................................ 7 mm
......................... 0-450 min
....................... 0-1800 min
.............................. 50 Nm
.............................. 60 Nm
.............................. 18 V
........................ 1,5-13 mm
............................. 1,7 kg
............................. 2,0 kg
............................. 2,4 kg
........................... 84,7 dB (A)
........................... 95,7 dB (A)
.............................. 13 m/s
............................. 1,5 m/s
........................... 0,95 m/s
............................. 1,5 m/s
........................... 0,66 m/s
............................. 1,5 m/s
18
A18 BS-2
-1
-1
2
2
22
2
22
2
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Sawdust and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas
or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can
cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. BTI off er to retrieve old batteries to protect our environment; please ask
your sales representative or our service line at 07940 / 141-141.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System BTI chargers for charging System BTI battery packs. Do not
use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with
soap and water. In case of eye contact rinse thoroughly for at least 10 minutes
and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to
a short circuit, never immerse your tool, battery pack or charger in fl uid or al-low
a fl uid to fl ow inside them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
30.01.2018 13:07:05 30.01.2018 13:07:05