Tabla de contenido
Idiomas disponibles
Idiomas disponibles
GB
During normal horizontal grass cutting it is recommended the use a spacer guard.
In the case of application of auxiliary wheels you should carry the auxiliary guard in the direction of the cutting head (VI). The
guard handle will lock it in the raised position. If you use the spacer guard you should lower it, and the handle will lock it in the
down position.
Replacing the line
The trimmer is equipped with a spool, which allows for unwinding of the line when you press the button on its bottom side. This
can be done during the operation of trimmer by hitting lightly with spool button the ground, as well as by pressing manually with
disconnected the power of trimmer.
During operation the trimmer you should not rest the switched on trimmer on a substrate, because it will cause complete unwind
of the line and wear of the whole stock wound on the spool.
It is not recommended to unwind the line over a length sufficient to reach the blade guard. After starting the trimmer, the line seg-
ment, whch is extending beyond the blade guard, is cut.
If you will not be able to further unwind the line, this means, that the line on the spool is worn and it should be replaced.
You should prepare a line section with a length and diameter shown in the table. Then remove the guard cover of the spool by
turning it clockwise (VII). Pull out the spool, then clean it and the inner housing of the spool.
In the middle of the length, put the line through the gap between two parts of the spool. Wind the line on the two parts of the spool
in the direction indicated by the arrow on the spool. You should leave about 15 cm line beyond the slots, it should be inserted
through the openings in the spool housing, and then you should assemble the cover on the spool housing.
Mount the spool in the spool guard by facing down the button. Then install the guard cover of spool and check whether the line
unwinds fspooly, by performing the above described manual test of its unwinding.
Preparing the workplace
Before starting work, you should prepare the workplace. Before starting the work you should assign a safety zone with a radius of
at least 15 meters away from the place of work. which will not be accessible for bystanders. Make sure, that around the workplace
there are not obstacles, which can cause collision of the operator or grass trimmer during its operation.
Connecting the grass trimmer to power (II)
Insert the battery into the power socket, with its pins facing to the inside of the shear and to the top, until the battery latches will
lock. Make sure, that the battery will not slip out during work.
You should disconnect the battery by pressing both clips, and then remove the battery from the grass trimmer housing.
Starting and stopping the grass trimmer
Make sure, that the battery is connected to the grass trimmer, and that from the cutting element protection was removed and that
the cutting element has no contact with any part of the body and other objects.
Adopt an position, that ensures balance. With one hand catch the front handle. With the other hand grasp the rear handle. Push
with your thumb the lock switch, and press the switch with other fingers, this will start the trimmer.
During operation it is not necessary to hold the lock.
The grass trimmer is stopped after releasing pressure on the switch. The cutting device can rotate for some time after the engine
is stopped. It is forbidden to stop the cutting element by applying pressing it to the ground or to other object.
After a complete stoppage of cutting element, you should disconnect the shear from the power supply by disconnecting it from the
battery. Then proceed to maintenance.
Work with the trimmer
Do not allow operation of the device at low rev speeds or during startup.
It is recommended, to move the grass trimmer from right to left during its work. Instead, you should avoid mowing, by moving the
trimmer from left to right. This will allow the operator to avoid, when cutting, the ejected remnants of cut grass.
Avoid mowing the shrubs and bushes. Work the grass trimmer near trees can damage their bark. Hitting with line stones, bricks,
walls or similar surfaces, can lead to very rapid wear of the line.
You should avoid cutting by the upper quadrant of the blade (IX). This will prevent the phenomenon of rebounding the trimmer
toward its operator in case of jamming of the blade during operation.
Tips useful when working
You should ensure balance and proper posture while you work. Be extremely careful when working on slippery, sloping or uneven
ground.
During operation, the cutting element must be constantly monitored. Do not carry out the cut in places which are remaining out
of sight.
Before you start your works, you should carefully inspect the work place, remove any loose branches and remnants of previous
cutting.
O R I G I N A L
I N S T R U C T I O N S
16
Tabla de contenido
