Product Service - Flo 79510 Manual De Instrucciones

GB
and bystanders. Prior to installation of the cutting element and cover to make sure that they are not damaged, have no cracks, are
not bent. Make sure, that there is at least 1 meter line on the spool.
During operation, it is likely, that objects can be thrown towards the operator and bystanders. The operator is responsible for
accidents or a threat presented to others or to the environment. Do not operate the device, if there are bystanders in the vicinity,
especially children and animals. Prior to work appoint a safety zone with a radius, of at least 15 meters from the place of work.
Despite the safety measures taken during the design and construction of the machine, there always remains a residual risk.
Therefore, you should use the technical and complementary protective measures.
Always wear eye and face protection, this protects the eyes, face and respiratory system against dust and objects thrown during
the operation. Always wear the correct, adjacent to the body, protective clothing. Use only long trousers. Do not wear loose cloth-
ing or jewelry. which can be caught by moving parts of the machine. Wear protective gloves and hearing protection. Wear safety shoes with non-slip soles, does not work with bare feet or sandals.
The device must be regularly reviewed in accordance with the information contained in the following section. This will allow for
more efficient and safer operation.
When you work you should use hearing protectors. Exposure to excessive noise can lead to permanent hearing damage.
Use protective glasses. During the work the garbage can create risk of eye injury.
You must be familiar with the instructions to switch off the device in case of emergency.
Before the work always check whether the cutting element, screws, guards and other elements are not worn or damaged. Replace
worn parts before starting work. You should also check that the screw connections not loosened. Tighten the loose bolts.
During operation, you should not tilt the machine and keep it constantly in a state of equilibrium, you should always put your feet
surely on the slope and walk, never run. When mowing slopes you should always move across the slope, never along.
Never touch the dangerous moving parts before disconnecting the machine from the power supply and until all dangerous moving
parts completely stop.
The cutting element can rotate for some time after the engine is stopped.
Disconnecting the machine from the power supply is to turn off the machine switch and disconnect the power source. Unplugging
the power cord from the wall socket in the case of mains-operated devices or disconnect the battery in the case of battery-powered
devices.
The machine should be disconnected from the power supply in every case when:
- the operator walks away from the machine,
- the obstruction is removed,
- before checking or cleaning,
- before the inspection whether machine is damaged after hitting the foreign object,
- before the immediate testing after the machine starts to vibrate excessively.

PRODUCT SERVICE

Preparation of grass trimmer to work Attention! Before all mounting and regulatory operations, you should disconnect the grass trimmer from the power supply. The
grass trimmer, which is mains powered, should be disconnected from the wall outlet, the grass trimmer, which is battery operated,
should be disconnect from the battery.
Visually inspect the tool, If you notice any damage, do not start any work before repairing them.
Installing the cutting element guard (II)
The guard translate around the spool, so the tabs hit in the gaps of cutting head. Then turn it back on again, so that it would be
install the guard with a screw.
Adjustment operations
The trimmer allows for adjustment of the front handle. To do this, you should loosen the screw which is securing the holder (III) and
then set the handle to the desired position and lock it with the screw. The handle position should be selected in an experimental
way, to fit the physical condition of the operator and the area in which the trimmer will be used.. The handle position should allow
work with the hands bent at the elbows and straight back. It should also ensure the freedom of movement in the plane of trimmer
work.
In addition to adjusting the position of the front handle, trimmer allows you to rotate the cutting head and length adjustment of
guard of the power supply cables.
The rotation of cutting head is possible when you pull and hold the lock button (IV) then rotation of the head by 90 degrees. re-lock
it by releasing the lock.
Setting the length of the wires guard is possible after loosening the lock ring (V) and then adjusting the length of the guard and
turning the lock ring. It is possible to steplessly adjust the length of guard in the area between movement delimiters.
At the edge of the guard there is a blade. which is used to automatically shorten the line. Before starting work, you should remove
from it the guard.
When using the trimmer for vertical cutting of edges (X). You can use the auxiliary wheels, which will facilitate the trimmer driving.
O R I G I N A L I N S T R U C T I O N S
15