General Description; Description Of The Control Panel; Manual Setting - Philips HR 4325/00 Manual De Instrucciones

6
This means: Position the Air Cleaner near the radiator or
other source of heating (fig. 6 - 7).
• Especially for allergic users it is advisable to use an Air
Cleaner in both the bedroom and the living room and to let
these run continuously or in the "Auto" function.
Which size of Air Cleaner is suitable?
To purify effectively the air in a domestic room or an area of a
room, all the air must pass the Air Cleaner filters 2 - 3 times per
hour.
Depending on the air contents of the room or area concerned:
• one Air Cleaner type HR 4325 should be used for rooms /
areas up to approx. 30 m
• one Air Cleaner type HR 4335 should be used for rooms /
areas up to approx. 50 m
Important
• Read these instructions in conjunction with the
illustrations before using the appliance. (Also see
fold-out page 3.)
• Do not immerse the appliance in water or other
liquids.
• Do not use the appliance outdoors or in a humid
environment.
• The appliance can be cleaned with a damp cloth.
First remove the mains plug from the wall socket.
• When disassembling: do not touch moving parts.
Allow the Rota filter to stop in its own time.
• Use only the original Philips filters.
• Do not obstruct the air inlet and air outlet grilles. Do
not place the appliance on a soft surface such as a
bed or couch.
• Keep the mains cord away from heated surfaces.
• If the mains cord of this appliance is damaged, it
must only be replaced by Philips or their service
representative, as special tools and/or parts are
required.
• The appliance has an influence upon the air
circulation in the room. In general, it is not advisable
to use it near an open hearth fire.
• After a power failure first switch the appliance on.
After this the clock and the timer can be reset.
• Do not expose the human sensor to a direct heat
source or rapid temperature changes.
• Switch off the "Auto" function if you leave the room
where the appliance is placed for a long time.
• Save these instructions for further reference.
7
2 floor surface;
2 floor surface.

General description

(fig. 8)
A
Air inlets (3)
B
Pre-filter
C
Rota filter
D
Fixing nut for Rota filter
E
Hepa filters
type HR 4325: 2 filters
type HR 4335: 3 filters
F
Control panel
G
Air outlet
H
Handle
I
Cord storage

Description of the control panel

J
On/Off button with indication light
K
On/Off button for automatic speed control ("Auto") with
indication light
L
Speed control with indication lights
1 = low speed
2 = normal speed
turbo = high speed
M
Button for timer and clock setting
N
Display
O
Buttons for setting the time (up and downwards)
P
Button 'reset' of Hepa filters replacement indicator
Q
Hepa filters replacement indicator (indication light)
R
Human sensor
Making ready for use
- Insert the mains plug into a wall socket.
The indication light above the on/off button, the digits (00:00)
and the clock symboll a start flashing. (This will also happen
after a power failure.)
The display is not
illuminated.
- Press the on/off switch (fig.
10).
The appliance starts
operating at speed 1 and
the display lights up
orange.
The indication light above
the on/off button remains
on to indicate that the
appliance is in switched-on
position.

Manual setting

11
- Switch the appliance on (fig. 11).
The indication light above the on/off button comes on and the
display lights up orange.
The appliance starts operating at speed 1.
- Select speed 1, 2 or "Turbo" by pressing the speed selector
(fig. 12).
5
(fig. 9)
10
12