Stid OEM Manual De Instrucciones

OEM Module 13.56 MHz
Installation instructions
TTL output:
MS-x31-E/103-xx
MS-x31-E/PH5-xx
7
6
5
4
3
2
1
Use an AC/DC power supply type LPS, Limited Power Source (as per IEC EN 60950-1 Ed2) or type ES1, PS1 (according to IEC EN 62368-1) for the main
supply.
Main power supply:
Max. consumption at 12 Vdc:
Regulated output:
Communication: Asynchronous RS232 serial link with TTL levels / TTL (Wiegand / Clock and Data).
Connector output: HE14 male 7 point.
Pull-up resistors: For Data signals, 10k pull-up resistors are connected internally to 3.3 Volts.
The initial status of the input "Switch" is memorized when the power supply is turned on.
If the status becomes different of the initial status, the reader is wrenched:
▪ for R/S 31(TTL): the wrenching signal will be emitted on the "Data/Data1" line. This function is configurable via a configuration card.
▪
for W31: the reader will perform the operations configured with the SSCP protocol.
R and S readers are configurable with the SCB configuration card created with SECard.
Caution: set your reader with your own company key.
▪ The supply voltage at the reader's connector should be between +4.5 Vdc and +9 Vdc.
▪ We recommend to use a filtered and regulated power supply.
▪ As far as possible, keep the reader away from computer or power source cables. They can generate electrical interference, depending on their radiation level
and the proximity of the reader.
▪ Maximum distance between reader and the controller board: 500 mm.
▪ Recommended distance between two readers: parallel plane: 15.8 in – same plane: 15.8 in – perpendicular plane: 11.8 in.
▪ Readers installed on a metal surface may have reduced performances.
▪ Connect the wires or the connector of the reader BEFORE powering on.
▪ Not connected pins NC* must be unconnected.
▪ The signals are of the RS232-TTL form, do not connect the reader directly to a RS232 serial port.
▪ Operating temperature: -4 °F to 158 °F / -20°C to +70°C.
Once the module has been integrated in its final environment, it is possible, if necessary, to tune it.
To do that, use a plastic screwdriver and adjust the tuning capacitor. Check the detection performance with different capacitor settings and keep the best.
More details about reader communication are available in the SSCP protocol specification.
2.36 in / 60 mm
General tolerance following ISO NFT 58-000 standard.
In accordance with the provisions of the Environment Code, STid finances the collection, decontamination and recycling of WEEE provided by
ESR-RECYLUM, to which STid adheres and to which it has transferred its regulatory responsibilities as a Producer.
STid recommends that owners of used equipment who wish to dispose of it return it as WEEE by contacting ESR / RECYLUM in order to benefit
from the solutions at no additional cost of collecting and recycling used equipment. More information on www.recylum.fr.
STid reserves the right to make change without notice, for the purpose of product improvement.
Range: +4.5 Vdc to +9 Vdc
180 mA
3.3 Vdc
1.38 in / 30 mm
0.39 in / 10 mm
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1057A06- Page 1 sur 3 - Ed. 11/06/2019
Module OEM 13,56 MHz
Notice d'installation
Product references
RS232 TTL output:
MS-x31-E/PH5-5AB
MS-W31-E/PH5-5AA
Pin R31
Wiegand
1
2
3 D0
4 D1
5 Clock
6
7
Power supply characteristics
Typical: 5 Vdc
Characteristics
Switch input
Read-only reader configuration
Precautions for installation
Tuning antenna module
Communication
Dimensions
0.1 in / 2.54 mm
"DEEE Pro" Member
Módulo OEM 13.56 MHz
Procedimiento de instalación
conforme con NOM-024 -SCFI-2013
x: R read only
S read only secure +
Type
R31 R31-W31
Clock & Data RS232- TTL
0 Vdc
+Vcc (+4.5 Vdc to +9 Vdc)
Code NC
Data Tx
Clock Rx
Switch
NC
US
FR
ES
0.197 in / 5 mm