Stid W11-B-E01-1A Instalación

OEM Module 125 kHz
Installation instructions
Pin number
W11-B-E01-1A Description
Data&Clock
R11-B-X01-2x Description
ISO 2
R11-B-X01-3x Description
Wiegand
R11-B-E01-5A Description
RS232 TTL
W11-B-E01-5G Description
RS232 TTL
1: Pin 1 is a reserved input and must be left unconnected.
2: the "Mode" input must be TTL compatible.
Main power supply:
Max. consumption at 5 Vdc:
Communication:
MS Connector output:
MDS Connector output:
▪ The supply voltage at the reader's connector should be between +5 Vdc and +5.5 Vdc.
▪ We recommend to use a filtered and regulated power supply.
▪ As far as possible, keep the reader away from computer or power source cables. They can generate electrical interference, depending on their radiation level
and the proximity of the reader.
▪ Maximum distance between reader and the controller board: 19.69 in / 500 mm.
▪ Readers installed on a metal surface may have reduced performances, the reader should be installed at no less than 2.76 in / 7 cm from any metallic surface.
▪ Connect the wires or the connector of the reader BEFORE powering on.
▪ Not connected pins NC must be unconnected.
▪ The signals are of the RS232-TTL form, do not connect the reader directly to a RS232 serial port.
▪ Operating temperatures: -4 °F to 158 °F / -20°C to +70°C.
More details about reader communication are available in: SP – Protocol1A(US).pdf for W11-1A, Spec_Protocole_5A_V1.0_EN.pdf for R11-5A,
Spécs_Protocole_PRG-St5x_5G_1.3.pdf for W11-5G.
1.06 in / 27 mm
General tolerance following ISO NFT 58-000 standard.
In accordance with the provisions of the Environment Code, STid finances the collection, decontamination and recycling of WEEE provided by
ESR-RECYLUM, to which STid adheres and to which it has transferred its regulatory responsibilities as a Producer.
STid recommends that owners of used equipment who wish to dispose of it return it as WEEE by contacting ESR / RECYLUM in order to benefit
from the solutions at no additional cost of collecting and recycling used equipment. More information on www.recylum.fr.
STid reserves the right to make change without notice, for the purpose of product improvement.
MDS
Antena conector
1
1
NC Read
Type Reserved
1
NC Mode
Type Reserved
1
NC Mode
Type Reserved
1
NC Mode
Type Reserved
1
NC Mode
Type Reserved
Range: +5 Vdc to +5.5 Vdc
MS: 20 mA // MDS: 85 mA
Asynchronous RS232 serial link with TTL levels / TTL (Wiegand / Clock and Data).
HE14 male 7 pins – Thread 0.1 in.
HE14 male 7 pins + 2 pins (antenna) – Thread 0.1 in.
0.94 in / 24 mm
Ø 0.157 in / 4.0 mm
Ø 0.197 in / 5.0 mm
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1018A02- Page 1 sur 3 - Ed. 12/06/2019
Module OEM 125 kHz
Notice d'installation
Product references
2 3
Clock Data
Input Input Input/Output
2
Clock Data
Input Input Output
2
Clock Data1
Input Input Output
2 1
NC Tx
Input - Output
2 1
NC Tx
Input - Output
Power supply characteristics
Typical: 5 Vdc
Characteristics
Precautions for installation
Communication
Dimensions
"DEEE Pro" Member
Módulo OEM 125 kHz
Procedimiento de instalación
conforme con NOM-024 -SCFI-2013
MS
4 5 6
Code +5Vdc
Output Input
Code +5Vdc
Output Input
Data0 +5Vdc
Output Input
1
NC +5Vdc
- Input
1
NC +5Vdc
- Input
1.18 in / 30 mm
1.06 in / 27 mm
US
FR
ES
7
0V
Input
0V
Input
0V
Input
0V
Input
0V
Input
Ø 0.134 in / 3.4 mm
Ø 0.098 in / 2.5 mm