Safety Of Persons; Power Tool Use And Care; Service; Chain Saw Safety Warnings - ATIKA KSH 710 SDS Manual Original

from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of cord
suitable for outdoor use reduces the risk of electric shocks.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shocks.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before turning
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hairs, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired. Power tool
that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tool. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the poser tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, being into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Power pruner safety warnings:
• Keep all parts of the body away from power pruner when
the chain saw is operating. Before you start the power
pruner, make sure the saw chain is not contacting
anything. A moment of inattention while operating power
pruner may cause entanglement of your clothing or body with
the saw chain.
• Always hold the power pruner with your right hand on
the rear handle and your left hand on the front handle.
Holding the power pruner with a reversed hand configuration
increases the risk of personal injury and should never be
done.
• Hold the power tool on the insulated handle surfaces as
the saw chain may come into contact with the unit's
mains supply cable. A contact of the saw chain with a live
conductor may apply hazardous voltage to metallic parts of
the unit and cause electric shock.
• Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet is
recommended. Adequate protective clothing will reduce
personal injury by flying debris or accidental contact with the
saw chain.
• Do not operate a power pruner in a tree. Operation of a
power pruner while up in a tree may result in personal injury.
• Always keep proper footing and operate power pruner
only when standing on fixed, secure and level surface.
Slippery or unstable surfaces such as ladders may cause a
loss of balance or control of the power pruner.
• When cutting a limb that is under tension be alert for
spring back. When the tension in the wood fibres is released
the spring loaded limb may strike the operator and/or throw
the power pruner out of control.
• Use extreme caution when cutting brush and saplings.
The slender material may catch the saw chain and be
whipped toward you or pull you off balance.
• Carry the power pruner by the front handle with the chain
saw switched off and away from your body. When
transporting or storing the power pruner always fit the
guide bar cover. Proper handling of the power pruner will
17