Ryobi RBS904 Manual De Utilización página 12

EN
FR DE ES IT NL
persons using original spare parts otherwise this may
result in considerable danger to the user.
BanD saw safEty warninGs
■ firmly clamp or bolt the saw to a work bench or leg
stand at approximately hip height.
■ never operate the saw on the floor.
■ avoid awkward operations and hand positions
where a sudden slip could cause your hand to move
into the blade. always make sure you have good
balance.
■ allow the motor to come up to full speed before
starting a cut to avoid binding or stalling.
■ Do not use tool if switch does not turn it on and off.
Have defective switches replaced by an authorised
service centre.
■ replacement parts. All repairs, whether electrical or
mechanical, should be made by a qualified service
technician at an authorised service centre.
■ when servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
■ Keep hands away from cutting area. Do not hand
hold pieces so small that your fingers go under the
blade guard. Do not reach underneath work or in
blade cutting path with your hands and fingers for any
reason.
■ never cut more than one piece at a time or stack
more than one workpiece on the saw table at a time.
■ Do not feed the material too quickly. Do not force
the workpiece against the blade.
■ use only correct blades. Use the right blade size and
style for the material and the type of cut. Blade teeth
should point down toward the table.
■ always support large workpieces while cutting to
minimize risk of blade pinching and kickback. Saw
may slip, walk or slide while cutting large or heavy
boards.
■ Do not remove jammed cutoff pieces until blade has
stopped.
■ Do not use saw bands which are damaged or
deformed.
■ replace the table insert when worn.
■ connect the product to a dust collecting device
when sawing wood.
■ Do not operate the product when the guard
protecting the saw band is open.
■ select the saw band and the speed depending on
the material to be cut.
■ Do not clean the saw band whilst it is in motion.
PT DA SV FI NO RU
English
PL CS HU RO LV LT
■ wear gloves when handling the saw band and
rough material.
■ use a push stick when straight cutting small work
pieces using the fence.
■ transport the product with the band guard fully
down and close to the table.
■ place the fence on the lower side of the table when
bevel-cutting with the table inclined.
■ use a suitable holding device when cutting round
or irregular shaped timber to prevent twisting of
the work piece.
■ Do not use guards for handling or transportation
■ adjust the adjustable guard as close to the work
piece as practicable.
■ never touch blade or other moving parts during use.
■ Before changing the setup and removing covers,
guards or blades, unplug the saw from the power
source.
■ Hold the workpiece firmly against the saw table.
■ to avoid accidental blade contact, minimize blade
breakage, and provide maximum blade support,
always adjust the blade guide assembly to just clear
the workpiece.
■ Keep blades clean, sharp, and with sufficient set.
Sharp blades minimize stalling and kickbacks.
■ always turn off saw before disconnecting it to avoid
accidental starting when reconnecting to a power
source.
■ Make sure work area has ample lighting to see the
work and that no obstructions will interfere with safe
operation before performing any work using your saw.
■ the blade guides have been preset at the factory.
These settings are functional for some applications.
We recommend that you check and adjust blade
guide settings before first use of your saw. Refer to
adjusting thrust bearings and blade guide support
procedures explained in the Adjustments section of
this operator's manual.
■ Do not use tool to cut metal.
■ this tool should have the following markings:
a) wear eye protection.
b) keep fingers away from the blade.
c) do not remove jammed or cutoff pieces until the
blade has stopped.
d) be sure blade is installed with teeth pointing down.
e) maintain proper adjustment of the blade tension,
blade guides, and thrust bearings.
f) adjust the upper guide to just clear the workpiece.
g) hold the workpiece firmly against the table when
cutting.
3
ET HR SL SK EL TR UK