Cautions For Use; Maintenance; Troubleshooting - Num'axes CANIFUGUE Pro Manual De Instrucciones

So that your dog quickly makes the connection between the stimulation and his bad behaviour, his attention must be attracted by first warning him
with the beep sounds.
The flags enable your dog to visualize the area where he can move freely and the boundary he must not cross.
− Give your dog plenty of encouragement
Let your dog make is training alone to start with. After the stimulation, as soon as he learns to obey and turn back, he should be patted; he will unders-
tand more quickly and his desire to obey will increase.
− Do not leave your dog unattended with the collar on until he is used to wearing it and you are satisfied that it is working correctly. You should ensure
that the stimulation level is adjusted correctly for your dog.
− When your dog has fully understood the connection between the stimulation and is bad behaviour, you can get on with your own jobs, but continue
to praise him at other times to reinforce his grasps of the concept of obedience.

Cautions for use

− Before using the pet fencing system, we advise you to have your dog checked by a vet to ensure it is fit to wear a collar.
− During thunderstorms unplug the transmitter power unit from the power outlet and especially disconnect the antenna wire connector from
the antenna wire socket.
− The CANIFUGUE PRO/CANIFUGUE MIX receiver collar is totally waterproof.
− The transmitter is not waterproof and must be installed indoor in a dry location (for example garage or garden shed): it can withstand tempe-
rature changes but will be damaged by water.
− The system activates automatically as soon as the dog enters the unauthorized zone. However, despite the product's excellent reliability, it may be
set off unintentionally.
− To avoid unintentional triggering, your dog should not wear a tag, metallic collar, or any other collar together with the pet fencing collar.
− Do not place or keep the unit in places exposed to high temperatures.
− Carefully check that your pet fencing system operates properly if it has not been used for some time.
− Do not adjust or test your product (boundary width, stimulations level) while the collar is on your dog.
− The collar should not be worn inside the house.
− The pet fencing system is a virtual boundary; you cannot consider it as a solid, foolproof barrier for all dogs.
− Each animal reacts to static stimulations and to training in a different way. Therefore, NUM'AXES cannot guarantee that your dog will stay, in all
circumstances, within the perimeter you have defined. There always will be a risk of escape. Instinct can overcome training especially when outside
distractions tempt your dog (cats, other dogs, balls, bikes, neighbours,...).
− Your dog's temperament may not be compatible with the product. Do not hesitate to contact a vet or professional trainer for any further advice.
− Keep your pet fencing system out of reach of children.
CANIFUGUE PRO receiver collar:
− Under no circumstances should you open the receiver collar. You could damage some components and endanger the waterproof function
of your product. Moreover, if you do this, your guarantee will be cancelled.
CANIFUGUE MIX receiver collar:
− In order to maintain water tightness, we recommend the replacement of the seal located in the receiver collar every year.
− Remove the battery from the receiver collar if you are not using the product for 3 months or more.
− Never leave a discharged battery in the receiver collar: leakage could damage your product.

Maintenance

Avoid cleaning the collar with volatile liquids such as solvents or cleaning fluids. Use a soft cloth and neutral detergent.
The strap can be washed with soapy water.

Troubleshooting

− Should your pet fencing system develop a fault, first read this guide over, then check the collar battery and recharge/replace it if necessary. Also
check that you are using the product correctly.
− Check the fit and tightness of the collar on your dog's neck. Make sure the contact points are in contact with the animal's skin. If necessary, replace
the short contact points by the long ones.
− Make sure the contact points are correctly tightened on the collar.
− Check the wire connection to the transmitter.
− Check the transmitter power supply (when the transmitter is On, indications appear on the LCD screen).
− If you encounter any problem of detection distances, check the condition of the wire and of the connections (oxidation, nick in the wire).
Gb - 24