Blaupunkt Boston RCC 45 Instrucciones De Montaje página 6

Notes on Safety
Instructions for installation and connection
Disconnect the minus pole of the battery during installation and connection.
When drilling holes, be sure not to damage any vehicle parts (battery,
cable, fuse box, etc.).
The positive cable must have a cross-section of at least 1 mm. The unit
is protected by a quick-acting fuse of 5 A.
Note:
By means of the support included in delivery you can mount the set in cars
with a DIN car radio cutout of 182 x 53 mm, an installation depth of 165
mm and an instrument panel thickness around the fixing clips of 1 - 20
mm, see fig. 1.
For cars with other cutout dimensions Blaupunkt delivers car-specific
installation kits for common car types for 50/52 mm sets. Use enclosed
distance plates only for installation kits of 52 mm sets.
Please check the dimensions and, if necessary, use a car-specific
installation kit, e. g. Audi A4/A6/A8: 7 608 0214 73.
When using installation sets for units of 52 mm, four distance plates,
order number 8 601 055 056 must be used, fig. 1a.
Preparation of car radio installation
Install the car radio into the DIN cutout provided in your car's dashboard
ex factory.
Prepare the car radio DIN cutout (unlock shelf or dummy cover) or cut out
the car radio compartment to 182 x 53 mm.
Grasp behind the car radio cutout and check how many of the fixing strips
of the car radio support may be bent.
Note: Try to bend as many fixing strips as possible.
Insert the support into the cutout and bend the appropriate fixing strips
with a screwdriver, see fig. 1, 2.
Connection
Notes on connection ..................................................................... fig. 4
Plus/minus connection .................................................................. fig. 5
Connection of equalizer and amplifier .......................................... fig. 6
4 speakers (4 Ω /7 W) ................................................................... fig. 7
Connection with multiple plug installed ex factory
For vehicles with a system plug installed ex factory Blaupunkt offers an
adapter cable for the common vehicle types, see fig. 8.
For Audi, Opel and VW vehicles an adaptor cable must be used although
these cars have a pre-equipped ISO connector. Otherwise the vehicle's
electric system will be interfered.
For vehicles prefitted with ISO connectors pins 1, 2 and 3 of the ±
connector must always remain free.
Connection with QuickOut installed ex factory
If your car is fitted with a QuickOut ex factory (at present Opel), the
QuickOut ex factory has to be removed, see fig. 8.
Ground cable
Do not connect the ground cable to the negative pole of the battery.
Route the ground cable to a suitable ground point (car body screw, car
body metal sheet) and shorten it accordingly.
Remove the insulation from the ground cable and attach the forked cable
lug (if necessary, solder it).
Scratch off the paint from the contact area of the ground point and
lubricate it with graphite grease (important for good ground contact).
Screw on the ground cable.
Positive cable (ACC 12 V) (ignition)
Connect the positive cable together with distributor to pin 30 (constant
power) or pin 15 (positive line connected via ignition) of the fuse holder
behind the fuse.
3 D95 653 021
GB
+12V
Permanent plus connection (Battery 12 V)
Connect the permanent plus terminal together with the cable and cable
clamp to a fuse-protected positive line (e.g. clock, warning flasher).
Control cable (Power Antenna +)
The control cable represents the switched positive output for external
components, e.g. amplifiers, equalizers, or motor antennas.
Do not connect the control cable to pin 15 (switched +) or pin 30
(permanent +12 V).
When installing an all-automatic motor antenna, connect the motor
antenna's control cable with a cable clamp to the control cable.
Car radio installation
Insert the car radio from the front into the support and push in until the
stop springs on the sides engage right and left (distinct click to be heard).
Removal of the car radio
Insert the brackets right and left into the provided trimplate holes and
push in until you hear a distinct click (lateral springs are unlocked).
Using both brackets (see fig. 3), pull the unit out.
Note: Locked brackets can only be removed after taking out the unit.
Modifications reserved
Notes de sécurité
Instructions de montage et de branchement
Pendant le montage et le branchement des appareils, il convient de
déconnecter le pôle négatif de la battérie.
Veiller à ce qu'aucun élément de voiture (tel que la battérie, les câbles,
les porte-fusibles) ne soit pas endommagé par le perçage des trous).
La section du câble positif ne doit pas eútre inférieure à 1 mm. L'appareil
est protégépar l'intermédiaire d'un fusible à déclenchement rapide 5 A.
Note:
A l'aide du support inclus dans le jeu de montage vous pouvez monter
le poste dans des voitures qui disposent d'une découpe DIN de 182 x 53
mm, d'une profondeur de 175 mm et d'une épaisseur du tableau de bord
de 5,2 - 6,3 mm autour des éclisses de montage, voir fig. 1.
Blaupunkt livre des jeux de montage spéciaux pour les voitures courantes
avec découpes différentes pour les appareils 50/52 mm.
Veuillez donc vérifier les mesures de la découpe de votre voiture et, si
nécessaire, commander un jeu de montage spécial,
p. ex. Audi A4/A6/A8: 7 608 0214 73.
En utilisant des jeux d'installation pour des postes de 52 mm il faut utiliser
4 plaques de distance, numéro de référence 8 601 055 056, fig. 1a.
Préparation pour l'installation d'autoradio
Monter l'autoradio dans la découpe autoradio prévue d'origine.
Ouvrir la découpe autoradio (dégager le compartiment ou le cache
factice) ou élargir la découpe à 182 x 53 mm.
Saisir derrière la découpe autoradio et essayer combien des éclisses de
montage peuvent être courbées.
Note: si possible, courber toutes les éclisses de montage.
Insérer le support dans la découpe et courber les éclisses correspondantes
à l'aide d'un tournevis, voir fig. 1 et 2.
Raccordement
Indication pour le raccordement ................................................... fig. 4
Positive/negative-Raccordement .................................................. fig. 5
Raccordement de l'égaliseur et de l'amplificateur ......................... fig. 6
4 Haut-parleurs (4 Ω/7 W) ............................................................ fig. 7
- 6 -
per. +12V
+12V
F