BLACK&DECKER J752BCB Manual De Instrucciones página 4

INTRoDUCTIoN
Thank you for choosing the Black & Decker 375 Amp Jump-Starter with 2A Battery
Charger/Maintainer. Please read this guide carefully before use to ensure optimum performance
and avoid damage to the unit or items that you are using it with.
FEATURES
12 VOLt DC ACCESSORY BAttERY StAtUS
OUtLEt (UNDER LED LIGHt ON/
pROtECtIVE COVER) OFF BUttON
BUILt-IN AC INpUt
pLUG FOR tHE
BAttERY CHARGER
FOLD-AWAY
HANDLE
tAB FOR
NEGAtIVE (–)
BLACK CLAmp
NEGAtIVE (–)
BLACK JUmp-
StARtER CLAmp
J752BCB_ManualENSP_061213.indd 6-7
BAttERY REVERSE
LED pOWER LEVEL pOLARItY
INDICAtORS BUttON INDICAtOR
JUmp StARtER
pOWER SWItCH
tWO LED AREA
LIGHtS
DOUBLE BARREL
BAttERY CHARGER/
mAINtAINER
CONNECtOR OUtLEt
UNDER pROtECtIVE
COVER (connects to
terminal rings, clamps
or vehicle adapter plug)
CHARGING StAtUS
LED INDICAtOR
tAB FOR
pOSItIVE (+)
RED CLAmp
pOSItIVE (+) RED
JUmp-StARtER
CLAmp
BUILt-IN 120 VOLt AC
JUmp-StARtER CHARGER
6
BAttERY CHARGER/ mAINtAINER
BAttERY CLAmpS
CHARGING/RECHARGING THE JUMP-STARTER, 12 VolT DC
PoRTABlE PoWER SUPPlY AND AREA lIGHT
Lead-acid batteries require routine maintenance to ensure a full charge and long battery life. All
batteries lose energy from self-discharge over time and more rapidly at higher temperatures.
Therefore, batteries need periodic charging to replace energy lost through self-discharge. When the
unit is not in frequent use, manufacturer recommends the battery be recharged at least every 30 days.
Notes:
This unit is delivered in a partially charged state – you must fully charge it upon purchase and before using it for the first time.
Initial AC charge should be for 24 hours.
Recharging battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will
reduce battery life. The battery can be recharged using the Built-In 120 Volt AC Charger.
Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
Important: If you know the unit is discharged, but the battery status LEDs illuminate as if fully charged when connected to a
charging power source, this may be due to the internal battery having a high impedance. The manufacturer suggests leaving the unit
on charge for a period of 24-48 hours before use.
CAUtION: RISK OF pROpERtY DAmAGE: Failure to keep the battery charged will cause permanent
damage and result in poor jump-starting performance.
Charging/Recharging the Jump-Starter Using the 120 Volt AC Charger and a
Standard Household Extension Cord (not included)
1. Lift the AC adapter cover located on the back of the unit and connect an extension cord to the unit.
Plug the other end of the cord into a standard 120-volt AC wall outlet.
2. Charge until the green Battery Status LED Indicator lights solid or flashes.
3. Disconnect the extension cord.
DOUBLE BARREL BAttERY
CHARGER/ mAINtAINER
CONNECtOR CABLE
(connects to terminal
rings, clamps or vehicle
adapter plug)
12 VOLt DC
VEHICLE
ADAptER pLUG
BAttERY
tERmINAL RINGS
7
6/12/2013 3:01:10 PM