Environmental Information - Flymo Hover Vac 250 Instrucciones De Empleo

• Is the grassbox fitted correctly?
• Are you using in straight lines?
• Are you cutting more than one third of the grass
length?
• Do you need to raise the cutting height?
• Follow the procedure described in "Poor Flotation".
SERVICE RECOMMENDATIONS
• Your product is uniquely identified by a silver and black
product rating label.

ENVIRONMENTAL INFORMATION

Husqvarna UK Ltd. products are manufactured under an
Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most
environmentally responsible manner, according to com-
pany procedures, and with the potential for recycling at
the end of the products' life.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised recycling.
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
GUARANTEE AND GUARANTEE POLICY
If any part is found to be defective due to faulty manu-
facture within the guarantee period, Husqvarna UK Ltd.,
through its Authorised Service Repairers, will effect the
repair or replacement to the customer free of charge pro-
viding:
a. The fault is reported directly to the Authorised Repairer.
b. Proof of purchase is provided.
c. The fault is not caused by misuse, neglect or faulty
adjustment by the user.
d. The failure has not occurred through fair wear and tear.
e. The machine has not been serviced or repaired, taken
apart or tampered with by any person not authorized by
Husqvarna UK Ltd.
f. The machine has not been used for hire.
g. The machine is owned by the original purchaser.
h. The machine has not been used outside of the country
for which it was specified.
i. The machine has not been used commercially.
• This guarantee is additional to, and in no way diminis-
hes the customers statutory rights.
Failures due to the following are not covered, therefore,
it is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine.
Vac250EU-20.960.01.indb 9
Excessive Vibration
NOTE:
Disconnect from the mains electricity
supply.
• Replace broken or missing plastic cutters.
• Check plastic cutters are fitted correctly.
• If vibration persists? Immediately disconnect from the
mains electricity supply and consult your local approved
Service Centre.
• We strongly recommend that your product is serviced
at least every twelve months, preferably by a professio-
nal.
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equip-
ment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for
the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where
you purchased the product.
Failures not covered by guarantee
• Replacing worn or damaged blades.
• Failures as a result of not reporting an initial fault.
• Failures as a result of sudden impact.
• Failures as a result of not using the product in accor-
dance with the instructions and recommendations
contained in this Operator's Manual.
• Machines used for hire are not covered by this guaran-
tee.
• The following items listed are considered as wearing
parts and their life is dependent on regular maintenance
and are, therefore not normally subject to a valid war-
ranty claim: Blades, Electric Mains cable.
CAUTION!
Husqvarna UK Ltd. does not accept liability under
the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement
parts or additional parts that are not either manu-
factured or approved by Husqvarna UK Ltd., or by
the machine having been modified in any way.
9
22.01.21 10:38