BlueAnt T1 Guia De Inicio Rapido

1
T1 Quick Start Guide: English
Multi-
Indicator
Function
Light
Button
(MFB)
Microphones
Vol + Vol -
2
Charge Your T1
Your T1 has been given an initial partial charge to get
started, but for best results charge it using the supplied USB
cable and adaptor until the indicator light turns white.
> Charge the T1 whenever it announces that the battery is
Very Low.
> A full charge takes about 3 hours.
> During charging, the indicator light fl ashes red.
> When the light goes white, the charge is complete.
3 Pair Your T1
1. Turn the T1 on by
sliding the power
switch on the back to
Power switch (on)
the green on position.
2. Put the T1 in your ear.
3. The fi rst time you use the T1 it will go straight to pair
mode and talk you through the pairing process.
For subsequent pairings, make sure the T1 is not
connected to any phones, then hold down the MFB. The T1
will announce that it is going into pairing mode.
Tip: The pairing code is 0000 (four zeros).
4 Transfer Your Phonebook
Once the pairing is complete, your T1 will attempt to transfer
your phonebook contacts so that it can announce the names
of incoming callers. Please accept any connection requests
from the T1 and wait for the transfer to fi nish.
Some phones do not support automatic phonebook
transfers. If the T1 announces that this is the case, you need
to go to your phone's address book and send contacts via
Bluetooth to the T1. See www.blueantwireless.com
Note: Whenever you add contacts to your phone in future
you must update your phonebook on the T1: with the T1
connected to your phone but not on a call, hold down the
MFB for 3 seconds to initiate a phonebook update.
5
Wearing the T1
You can wear your T1
on either ear.
For best results:
> Position the hook and
ear gel as shown here.
Charging
Port > Make sure the T1 is angled
towards your mouth.
Protective Skins
Your T1 is supplied with optional rubber
skins to protect against dust and
moisture.
6
Making Calls
Use your voice to make calls:
1. Click the MFB and wait for the T1 to ask you
to Say A Command.
2. Say Phone Commands to activate the voice
dial feature on your phone (if supported by
your phone).
Or:
> Dial the number on your phone and the audio will
automatically transfer to the T1.
> Hold down Vol + for 1 second to redial the last outgoing
call.
7 Taking Calls
When the phone rings, you can answer the
call with your voice: wait for the prompt to ask
you if you want to take the call, and then say
Answer or Ignore.
If you don't want to wait for the prompt, or you
are in a noisy place:
> Click the MFB once to accept the call.
> Double click the MFB to reject the call.
During a call, click the MFB to end the call.
8 Voice Commands
To use any of the voice commands, click the MFB, wait for
the T1 to ask you to Say A Command, then say the command:
> Check Battery — Tells you the battery level on the T1.
> Call Information — Calls an information service number
stored in your headset. Call charges may apply.
> Phone Commands — Activates your phone's voice dialing
feature (if available on your phone). Depending on your
for help.
phone model, you may need to record voice tags on the
phone to use this feature.
Voice recognition will cancel automatically after a short
period of time if you do not say a command. You can also
cancel voice recognition by clicking the MFB.
9
Listening to Audio
The T1 supports A2DP audio streaming: if your phone or
Bluetooth device supports the A2DP profi le then you can
simply start playing music or any other audio (including
LEFT RIGHT
directions from a GPS application on the phone) and it will
EAR EAR
automatically transfer to the T1.
The audio will mute automatically if you make or receive a
phone call, and resume when the call ends.
10
Multipoint
Up to 2 phones can connect to the T1 at the same time. To
pair a second phone:
1. Use your phone's Bluetooth menu to disconnect the
existing paired phone from the T1.
2. With the T1 switched on, hold down the MFB until the T1
starts to talk you through the pairing process.
3. When the pairing is complete, use the Bluetooth menu on
each phone to reconnect them to the T1.
When you have 2 phones connected, you can always answer
a call on either phone. If you initiate a call through the T1 it
will happen on the "primary phone": the one that connected
to the T1 fi rst.
11 Advanced Button Functions
> To hold an active call and switch to an incoming or held
call, press Vol + for about 1 second.
> To end an active call and answer a new incoming call,
press Vol - for about 1 second.
> You can conference two active calls together by holding
the MFB for 3 seconds (if your phone and network support
this).
> To transfer audio to the phone, click
together during a call.
> To disconnect your phone from the T1, click
together when you are not on a call. Hold down
about 1 second to reconnect.
12 Advanced Button Functions
> During a call you can mute and unmute the T1 microphone
by holding Vol + and
(about 1 second).
> Whenever you add contacts to your phone you must also
update your phonebook on the T1: with the T1 connected
to your phone but not on a call, hold down the MFB for 3
seconds to initiate a phonebook update.
> To turn the fl ashing indicator light on or off, disconnect
the T1 from your phone and hold down
1 second.
> Click the MFB to: end a call, cancel pair mode, cancel voice
recognition, or cancel a phonebook transfer/update.
13
Upgrades
To enhance your experience, we are continually upgrading
the T1 fi rmware.
From time to time we will make upgrades available on our
website for you to download and apply to your T1.
Go to www.blueantwireless.com
upgrades available for your T1.
You must register your product online at
register.blueantwireless.com
upgrades.
14
Reset your T1
If you are having problems with the T1, you can reset the T1
and your phone and start again:
1. Disconnect the T1 from your phone by deleting the pairing
from your phone's Bluetooth menu.
2. Turn your phone off and back on again to clear its memory.
3. With the T1 switched on, but not connected to any phones,
click all three buttons
The T1 will reset and go straight to pairing mode.
You will now need to pair your phone with the T1 again.
15 Help and Support
This guide is just to get you started with the T1. If you
are having trouble getting the T1 to work, please visit
www.blueantwireless.com
troubleshooting tips.
Please call us before returning the T1 to a store and we will
help you through any diffi culty you may have.
> North America:
Vol + and Vol - > Australia:
> New Zealand:
Vol + and Vol -
Vol + for
16 Terms and Conditions
By using this product you are agreeing to BlueAnt's terms
Vol - together until the T1 beeps twice and conditions, available at www.blueantwireless.com.
Warning:
of up to 100 decibels. Prolonged use at high volumes may
affect your hearing capacity. Using for extensive time periods
may result in noise induced hearing loss (NIHL). Please read
the enclosed safety card for information about the safe use
of BlueAnt products.
Vol + and Vol - for The Bluetooth
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by BlueAnt Wireless is under license.
© 2010 BlueAnt Wireless. All Rights Reserved.
for full details on the latest
for access to fi rmware
(Vol +, Vol -, and the MFB) together.
for online help, support, and
1866 891 3032
1300 669 049
0800 443 122
All BlueAnt devices are designed to reach volumes
® word mark and logos are registered
Version: T1-QSG-USEN-1.2