Metalux LCHB Instrucciones

LCHB High Bay
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Wire Cutters
• Screw Driver
• Safety Glasses
• Gloves
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards-Installation and mainte-
nance of this product must be performed by a qualified electrician. This product must
be installed in accordance with the applicable installation code by a person familiar
with the construction and operation of the product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation
or attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury and
property damage.
CAUTION
• Connect fixture to power source noted on product identification label. Any
other connection voids the warranty.
• Fixture should be installed by persons with experience wiring or by a qualified
electrician. The electrical system, and the method of electrically connecting the fixture
to it, must be in accordance with the National Electrical Code and local building codes.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
GENERAL WIRING DIAGRAM
Black (Line)
120-277v
White (Neutral)
Green (Ground)
Dimming Wire To
0-10v Control
Questions?/ Questions / ¿Preguntas?/ 1-800-334-6871 www.eaton.com/lighting
PACKAGING CONTENTS /CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
A. Light fixture with lens
L'appareil d'éclairage avec lentille
Accesorio con la lente
LED Driver
OUTPUT
To LEDs
B. (2) Wire Hanger
Crochet de suspension métallique
Gancho para cables
INSTALLATION
Chain Kit (included)
1
INSTALLATION STEPS
WARNING: Always turn Off the supply from main circuit breaker first!
• Remove the LED luminaire from packaging and inspect for any damage. Handle LED
luminaire with care.
• TO INSTALL WITH CHAIN MOUNT: Install the chain into the provided wire hanger. Secure the
other end of the chain to a structure using hardware rated for the load. Install the wire hanger
into the slots on the top of the LED luminaire end piece. (Fig. 1)
• Make sure the wiring hangers are fully engaged into the slots on the top channel. (Fig. 2)
• Close all open hooks on chain and wire hanger to secure mounting and fixture.
• Connect the LED high bay wiring to incoming power lines, with black to black, white to
white and green to green. Use only UL listed wire.
NOTE: The purple and grey wires inside the driver compartment are 0-10V (Iow voltage) dimming
wires. Connect to low voltage wiring only. Clean all residues and fingerprints from the LED
luminaire. Double check all hanging hardware before moving onto the next installation.
LENS REMOVAL
1. Remove the screws attaching the lens end cover to
the luminaire body, and remove the lens end cover.
2. Slide the lens out of the luminaire body.
1
Instruction Manual/Directives/Instrucciones
C. (2) Chains (24" Long)
Chaîne
Cadena
2