Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Frame rail
Fasteners
typical
both sides
Figure 1
Conical washer
teeth side
against hitch
1.
Remove underbody panel: If applicable, using 7mm socket and screwdriver remove the screws and plastic push rivets that hold the underbody panel in place. Remove the underbody panel
between the mufflers. Return to vehicle owner or trim to fit and reinstall. Note: Extensive trimming would be required.
2.
Lower Exhaust – Using a 10mm socket remove the bolt from the exhaust hanger on the outboard side of the frame rail, push hanger up and outward to remove from the frame rail. Using
exhaust hanger removal pliers, remove the rubber exhaust hanger near the rear differential. Be sure to support the exhaust to prevent damage. Set fasteners aside for reinstallation.
3.
Remove heat shields - Using a 10mm socket, remove the nuts holding the heat shield, and using a 7mm socket, remove the screw holding the heat shield to the wheel well liner and the
fascia, remove the heat shield. Cut a 1.5" hole forward of the center attachment in the heat shield to clear the middle fastener for the hitch, see Fig. 2. Set fasteners aside for reinstallation.
4.
Remove M16 bumper bolt – Using a 21mm socket remove the bumper bolt from the bottom of the frame rail. Set aside for reinstallation.
5.
Remove rearmost fascia fasteners – Remove the plastic push rivets from the rearmost lower edge of the fascia. Set fasteners aside for reinstallation.
6.
Remove Kick Sensor (If applicable) – Using a ¼" drill bit remove the center (4) rivets holding the kick sensor in place.
7.
Trim fascia – If applicable, move the kick sensor aside to avoid cutting during trimming. Find the center of the fascia and trim the vehicle fascia per Fig. 3. *Dimension are approximate.
8.
Install hitch – Using the supplied pullwires
sure weldnuts are free from rust and debris. Raise the hitch into position and align holes in hitch bracket to the frame rail weldnuts guiding the pullwire ends through holes in the hitch bracket
and loosely reinstall the M16 bumper bolts removed in step 4. Remove pullwires, install conical washers
9.
Tighten all M16 fasteners with torque wrench to 146 Ft.Lb. (198 N*M), 1/2" fasteners to 75 Ft.Lb. (102 N*M)
10. Reinstall modified heat shields – Reinstall the modified heat shields back into place over the hitch bracket using all fasteners removed earlier. Reinstall fascia fasteners.
11. Reinstall exhaust and kick sensor – Reinstall the kick sensor, raise exhaust back into position and reinstall all exhaust hangers and fascia fasteners.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be
removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices
and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2020, 2021 Horizon Global™ Corp - Printed in Mexico
Installation Instructions
PART NUMBERS: 76320, 84320, CQT76320
①②
Center
Attachment
Rivets
lm
M16 Bumper
Bolt
n
install the carriage bolts ①and spacers ② into the vehicle frame through the center attachment, see Fig. 4, leave pullwires attached. Make
5"
Figure 2
5"
3.25"
A. Insert bolt and
Figure 3
l
m
(teeth side toward hitch) and nuts
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 3 of 36
76320NP
Fastener Kit: 76320F
①
Qty. (4)
Carr. Bolt ½-13x1.25"
GR5
②
Qty. (4)
Spacer .250"x1"x 3"
Part #: 3022
Qty. (4)
Conical washer 1/2"
l
Part #: 01292008
Qty. (4)
Hex nut
m
1/2'', GR5
Qty. (4)
Pullwire 1/2''– 13
n
Part #: 5482
Qty. (4)
Rivet Part # 110269
o
⑤
Kink pullwire to keep spacer independent of bolt
B. Align block
C. Pull bolt
Block into
on
thru block
access hole
frame
Figure 4
, see Figure 1.
5-27-21
Rev. D
Tabla de contenido
