Idiomas disponibles
Idiomas disponibles
H-6697
SHOWER EYEWASH STATION
TOOL NEEDED
NOTE: Unit is furnished with corrosion resistant
epoxy coating, care must be taken to avoid
damaging finish during assembly. For best
results, a strap wrench should be used.
IMPORTANT! All threads are tapered pipe and require pipe joint compound or Teflon tape to assure watertight
connection. When securing with Teflon tape, wrap tape around each thread 10-12 times for optimal seal.
1.
Unscrew large shower connection pipe (1) from elbow (2) and shower ball valve (3).
Wrap Teflon tape around threading and reassemble.
2. Unscrew small shower connection pipe (4) from shower ball valve (3).
Wrap Teflon tape around threading and reassemble.
3. Assemble the shower head (5) onto the elbow (2)
and set assembled parts aside.
4. Unscrew square head plug (6) from top inlet tee (7).
Wrap Teflon tape around threading and reassemble.
NOTE: If the top inlet tee (7) will be where the water
source is supplied, screw square head plug (6) into
side of middle inlet tee (8) instead.
5. Wrap tape around threading of base support unit (9)
and connect to eyewash basin connection pipes (10).
6. Attach eyewash basin (11) to basin connection pipes (10).
7.
Wrap tape around threading of middle pipe section (12)
and connect to basin connection pipes (10).
8. Connect hose (13) to ball valve and position for proper
access by users.
9. Wrap tape around threading of top pipe section (14)
and assemble to top of middle inlet tee (8).
10. Take assembled shower connection pipe from steps 1-3,
wrap with tape, and connect to the side of the top inlet
tee (7) so that the shower head (5) is facing down for
proper use.
11. Attach the pull handle (15) to arm of the ball valve (3).
12. Connect water line to top inlet tee (7) or middle inlet
tee (8) – square head plug (6) should be in the tee that
doesn't have the water supply.
13. Secure unit to floor and run water through pipes to flush
out any impurities and test for proper operation.
PAGE 1 OF 6
1-800-295-5510
uline.com
Strap Wrench
ASSEMBLY
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
NOTE: The use of a vice is recommended for
proper tightening and alignment.
1
2
3
5
15
11
10
6
4
7
14
8
12
Push
Handle
13
9
0721 IH-6697
Tabla de contenido
Manuales relacionados para Uline H-6697
Resumen de contenidos para Uline H-6697
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-6697 1-800-295-5510 uline.com SHOWER EYEWASH STATION TOOL NEEDED Strap Wrench ASSEMBLY NOTE: Unit is furnished with corrosion resistant NOTE: The use of a vice is recommended for epoxy coating, care must be taken to avoid proper tightening and alignment.
- Página 2 Fittings 86" Heads Eyewash Basin 16 x 10½" 11¼" Push Handle 64¼" 7½" 5/16" Mounting 44" Slots 1¼" NPT outlet 6¼" 8" This unit complies with the requirements of ANSI Z358.1. 1-800-295-5510 uline.com PAGE 2 OF 6 0721 IH-6697...
-
Página 3: H-6697 Estación Lavaojos Con Regadera
H-6697 800-295-5510 uline.mx ESTACIÓN LAVAOJOS CON REGADERA HERRAMIENTA NECESARIA Llave de Correa ENSAMBLE NOTA: La unidad se suministra con un NOTA: Se recomienda usar un tornillo de banco recubrimiento epóxico resistente a la corrosión, para apretar y alinear de manera adecuada. -
Página 4: Continuación De Ensamble
Lavabo del 16 x 10½" 11¼" Lavaojos Manija de Empuje 64¼" 7½" Ranuras de 44" Instalación de 5/16" Salida NPT de 1¼" 6¼" 8" Esta unidad cumple con los requisitos de ANSI Z358.1. 800-295-5510 uline.mx PAGE 4 OF 6 0721 IH-6697... - Página 5 H-6697 1-800-295-5510 uline.ca DOUCHE/DOUCHE OCULAIRE OUTIL REQUIS Clé à sangle MONTAGE REMARQUE : L'appareil dispose d'un revêtement REMARQUE : L'utilisation d'un étau est en époxy résistant à la corrosion. Veillez à ne recommandée pour obtenir un serrage et un pas endommager le fini lors du montage. Pour alignement adéquats.
- Página 6 64 1/4 po 7 1/2 po Trous de fixation 44 po de 5/16 po Sortie NPT de 1 1/4 po 6 1/4 po 8 po Cette unité est conforme aux normes ANSI Z358.1. 1-800-295-5510 uline.ca PAGE 6 OF 6 0721 IH-6697...