Care And Maintenance; Environmental Protection; Technical Specifications - Metabo DKG 80/16 Manual Original

Ocultar thumbs Ver también para DKG 80/16:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 33
en
ENGLISH
air source immediately and forward it to a specialist
for inspection.
.

7. Care and Maintenance

Danger! Disconnect the compressed air con-
nection and empty the magazine before car-
rying out any work on the tool.
Danger! Repair and maintenance work other
than the work described in this section should
only be carried out by qualified specialists.
- Protect the compressed air connections of the
stapler and the hose line against contamination.
- Carry out regular maintenance to ensure the
safety of the air tool.
- Check that all screw fittings are seated securely,
and tighten if necessary.
- Clean the filter in the compressed air connection
at least once a week.
- It is recommended that you install a pressure
reducer with an air-water separator and lubricator
upstream of the air tool.
- If a large amount of air or oil is escaping, check the
air tool and have it maintained if necessary. (See
Section 9.)
f
8. Accessories
Use only genuine Metabo accessories.
Only use accessories that are designed for this air
tool and that fulfil the requirements and the specifi-
cations listed in these operating instructions.
For a complete range of accessories, see
www.metabo.com or the catalogue.
9. Repairs
Danger! Repairs to the air tools must only be
carried out specialists using original Metabo
spare parts and who observe the specifications in
the operating instructions!
('Specialists' are persons who, on the basis of their
technical training and experience, have sufficient
knowledge in the area of staplers and who are suffi-
ciently familiar with the relevant statutory occupa-
tional safety regulations, accident prevention regu-
lations, directives and generally recognised
technological rules that they are able to assess the
status of staplers with regard to work safety.)
If you have Metabo air tools that require repairs,
please contact your Metabo service centre. For
addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

10. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on recycling. You must not
cause risks to people or the environment.
Do not dispose used tools with household
trash; dispose of properly at a collection point
16
for recycling disused machines, packaging and
accessories.

11. Technical Specifications

Explanatory notes on the specifications on Page 3.
Subject to change in line with technological
advances.
V
= Air consumption per fastening operation
p
= Recommended operating pressure
p
= Maximum permissible supply pressure
max.
L
= Filling capacity of suitable compressors
C
AS
= Type of actuation:
S
= Sequential actuation
1
S
= Sequential actuation with safety
2
sequence
C = Contact actuation
Explanation:
Sequential actuation: The trigger (9) must be actu-
ated for every fastening operation. For each addi-
tional fastening operation, the trigger first has to be
moved back to initial position.
Sequential actuation with safety sequence: For
each fastening operation, the trigger (9) and trigger
safety lock (3) must be actuated so that a single
fastening operation is initiated via the trigger after
the opening of the tool is placed on the fastening
point. Additional fastening operations can only be
actuated if the trigger and trigger safety lock are in
initial position.
Contact actuation: For every fastening operation,
the trigger (9) and trigger safety lock (3) must be
actuated, whereby the order of actuation is not
defined. For subsequent fastening operations, it is
sufficient either if the trigger remains actuated and
the trigger safety lock is actuated, or vice versa.
Finishing nails that can be used:
N
= Type
Typ
N
= Length
L
N
= Wire thickness
T
Staples than can be used:
K
= Type
Typ
K
= Back width
B
K
= Length
L
K
= Wire thickness
T
A
= Dimensions:
Length x Width x Height
m
= Weight (without fasteners)
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this tool and compare these with the
values emitted by other tools. The actual values
may be higher or lower, depending on the particular
application and the condition of the tool or mounted
tool. In estimating the values, you should also
include work breaks and periods of low use. Based
on the estimated emission values, specify protec-
tive measures for the user - for example, any organ-
isational steps that must be put in place.
Tabla de contenido
loading

Tabla de contenido