Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2.2. SAFETY IN THE WORKPLACE
a)
Only the manufacturer's service point may repair the
device. Do not attempt any repairs independently!
b)
Regularly inspect the condition of the safety labels. If
the labels are illegible, they must be replaced.
c)
Please keep this manual available for future
reference. If this device is passed on to a third party,
the manual must be passed on with it.
d)
Keep packaging elements and small assembly parts
in a place not available to children.
e)
Keep the device away from children and animals.
2.3. PERSONAL SAFETY
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
The device can be handled only by physically fit
persons who are capable of handling it, properly
trained, familiar with this manual and trained within
the scope of occupational health and safety.
c)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
d)
Remove all adjusting tools or spanners before
turning the device on. A tool or spanner left in the
revolving part of the device may cause injury.
e)
The device is not a toy. Children must be supervised
to ensure that they do not play with the device.
EN
2.4. SAFE DEVICE USE
a)
Do not overload the device. Use the appropriate
tools for the given task. A correctly-selected device
will perform the task for which it was designed better
and in a safer manner.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c)
Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements and
for any other conditions which may impact the safe
operation of the device. If damage is discovered,
hand over the device for repair before use.
d)
Keep the device out of the reach of children.
e)
Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
f)
Clean the device regularly to prevent stubborn grime
from accumulating.
g)
The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
h)
Keep the device away from sources of fire and heat.
i)
Do not overload the device.
j)
Keep batteries out of reach of children when not in
use.
k)
Before use, make sure that the wind turbine and
the rotor are not blocked in any way, which would
disturb the measurement results.
l)
The external transmitter should be mounted in
the open air in a place where it can be exposed to
weather conditions. Mounting close to canopies,
walls or trees may result in disturbing the
measurement results.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
The device is intended for meteorological measurements,
incl. temperatures, rainfall, air humidity, wind speed, etc.
The user is liable for any damage resulting from
unintended use of the device.
ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 129-130).
3.1. DEVICE DESCRIPTION
3.1.1. TRANSMITTER
1.
Wind direction indicator
2.
Wind speed meter
3.
Light sensor
4.
Humidity / temperature meter
5.
Precipitation level meter
6.
Level
7.
Solar panel
8.
Pin "U"
9.
Battery compartment
10.
[RESET] button
11.
LED diode
3.1.2. RECEIVER
1.
The RF- lamp will light up when the radio frequency
reception is working properly.
2.
INDOOR lamp will light up when the inside sensor is
connected.
3.
OUTDOOR lamp will light up when the outside
sensor is connected.
4.
WiFi lamp will light up after connecting to the
hosting service.
5.
POWER lamp
6.
RESET button
7.
Power connection
3.2. PREPARING FOR USE
ASSEMBLING THE APPLIANCE
CAUTION: Before installing the weather station in a target
place, configure the set and, afterwards, check if the device
is working properly.
Inserting batteries
1.
Remove the battery compartment cover.
2.
Insert the batteries into the compartment observing
the polarity
3.
Replace the battery compartment cover.
Note: If you need to replace the batteries with new
ones, proceed in the same way as above.
Note: If none of the LEDs are lit, please make sure
the batteries are inserted correctly or the reset was
correct.
Note: If the temperature can drop below 0° C, better
use lithium batteries instead of alkaline ones.
22
3.2.1 CONFIGURING THE SET
A.
Transmitter
1.
After installing the batteries, the transmitter will start
for a short time and this will be indicated by the LED
light. Then the LED will turn off and the transmitter
will go into normal operation mode.
2.
A transmitter will start searching for a radio time
signal. If a signal reception is correct, a diode will
flash and, afterwards, light for several seconds.
3.
When operating in a standard mode, a diode will
light for a moment every 48 sec.
B.
Receiver
If the signal is lost or the measurement results are
not displayed:
a)
press and hold the [RESET] button on the transmitter;
b)
take out the batteries and after about 2 minutes
put them back into the battery compartment of the
receiver.
TRANSMITTER INSTALLATION
A.
Mounting bracket
1.
Unpack the transmitter components and check their
condition.
2.
Attach a metal flat bar to the bottom of the
transmitter.
3.
Insert the "U" pins into the holes of the flat bar and
secure them with the nuts.
B.
Wind speed meter (anemometer)
1.
Mount the measuring cups on the shaft. Secure by
tightening the bolt.
Note: pay attention that the anemometer cups can
move freely. Too tight mount can interfere with
measurement results.
C.
Wind direction indicator (anemoscope)
1.
Mount the weathercock on the shaft by sliding it
all the way to the opposite side of the anemometer
and secure it by tightening the bolt.
Note: make sure that the weathercock can move
freely.
D.
Outdoor installation
1.
Place the transmitter in its final location using the
mounting bracket (post ø = 1 "÷ 2" not included in
the set).
2.
When installing a transmitter in a target place,
take account for a north direction and install the
transmitter according to the direction which is
marked on a transmitter surface.
3.
Level the transmitter using a level which is placed on
its surface. Caution: Poor levelling of the transmitter
may disturb measurement results.
RECEIVER INSTALLATION
1.
It is recommended to install a receiver on a flat,
vertical surface to provide a proper transmitter
signal reception. Caution: a distance from a
transmitter, the appearance of barriers (e.g. walls),
electromagnetic and radio waves may reduce the
power of a signal.
3.3. DEVICE USE
To connect the device to the network, you must download
the APP WS View application to the mobile device (it. 4).
3.3.1. LIVE DATA
After selecting the "DEVICE LIST" from the main setup
menu, please select "LIVE DATA". All parameters will be
displayed.
23
EN
Tabla de contenido
