Tabla de contenido
Idiomas disponibles
Idiomas disponibles
• Press and hold Talk back button (12) to talk to the baby. The Talk icon will be shown at the left lower corner of the LCD
screen. The Music playback will stop if Talk back is activated.
.
5.5
Adjusting the volume of the parent unit
In normal mode, press Up (3) or Down (4) button to adjust the volume of the parent unit
6. Menu
6.1 Brightness
1. Press Menu button (7) once to select Brightness.
2. Use Up (3) or Down (4) button to adjust the LCD brightness level to 1, 2, 3, 4, or 5 (default
setting=3). The LCD brightness display will change accordingly.
6.2 Temperature C/ F
1. Press Menu button (7) twice to select Temperature.
2. Use Up (3) or Down (4) button to adjust the temperature display to C, F, or Off (default= C).
The temperature unit and reading will change accordingly. During the setting, the temperature icon
6.3 Night Light
1. Press Menu button (7) three times to select Night Light.
2. Use Up (3) or Down (4) button to turn the Night Light function On or Off.
The night lights on Baby unit will be switched on and off accordingly.
6.4 Vibration
1. Press Menu button (7) four times to select Vibration function.
2. Use Up (3) or Down (4) button to select the vibration function On or Off.
When this function is on, the parent unit will vibrate as soon as the sound level led is exceeding the red level.
Remark: the parent will NOT vibrate when it is under charging.
6.5 VOX
1. Press Menu button (7) five times to select VOX option.
2. Use Up (3) or Down (4) button to adjust the VOX level to OFF, 1, 2, 3, 4 or 5 (default=OFF)).
When the VOX function is on (level 1 to 5), the LCD on the parent unit will be off after the menu operation is done, and
the VOX led will be on.
The parent's unit LCD will be switched on;
1. When the baby sound hits the VOX threshold.
2. Any key on the Parent unit is pressed.
6.6 Select Camera
VM2400 can pair up to max. 4 cameras and the icon Cx will be shown on the upper right hand corner of the screen. The user
can select their favorite camera by following this:
1. Press Menu button (7) six times to select the Camera option.
2. Use Up (3) or Down (4) button to select the camera (C1, C2, C3, C4 and Auto) that you want to review.
C1 = Camera 1
C2 = Camera 2
C3 = Camera 3
C4 = Camera 4
Auto = the display will show each camera view for 15s.
Remark:
(a) If the select camera is not existing, not in range or not registered to the system, the screen will be blank and the
out of range icon will be on
(b) In case some registered camera cannot be found during Auto mode, the system will continue to look for them for
2 rounds. Afterward, the system will skip those missing camera and will just show the available camera screen.
7. Registration
7.1 Baby Monitor operation
When using the Baby Monitor, do not bring the Parent unit too close to the Baby unit, otherwise you could cause
feedback between the two units, which will result in a loud howling noise.
7.2 Baby monitor registration
Parent unit, and you do not need any further registration between them. However, if the
Baby unit loses the link with the Parent unit it may need to be re-registered, in which case follow the instructions
below:
Baby unit/Parent unit
1.
Switch the baby unit off. Switch set to OFF
2.
Cover the light sensor with a black cloth and switch the baby unit on. Position ON
3.
With the parent unit switched on press and hold this button on the parent unit for a few seconds.
4.
This icon appears in the display
5.
The power LED on the baby unit flashes quickly for approx. 15 seconds
6.
Press this button to confirm the selection.
7.
C1....appears initially, then C1....OK
When a connection is established, the image viewed by the lens appears in the display.
Note: If the C1...X appears(registration failed), it maybe necessary to remove the power and the batteries from the
baby unit for a few seconds.
will display.
SPECIFICATION FOR MODEL NO.: CCTV-4245B
Energy Saving
Multi-Camera
Talking Range Approx.
LCD Type
Frame rate
Brightness and contrast controls.
Out of range warning
Battery low warning
Temperature monitor
Talk back
Vibration
Energy saving with voice detection
Up to 4
outdoor 150m (LOS)
2.4" Color screen: 480(RGB) x 234 Delta LCD
Up to 8 Frames per second (Adaptive)
Brightness only
Yes, icon display on LCD and optional beep sound
Yes, led and optional beep sound
Yes
Yes
Yes
Tabla de contenido
