Premier CCTV-4245B Manual De Instrucciones página 11

9 Battery Compartment To fit the 4xAAA alkaline battery
3.3 What the symbol means
Icons Functions
It is on when the baby unit is out of range
It is on when setting the temperature reading or when the temperature
reading is on
It will show up when the temperature is too high
It will show up when the temperature is too low
Icon for setting Night Light function
The talk back function is activated
It is on when playing back the lullabies
It is on when adjusting the volume of the parent unit
It is on when adjusting the brightness of the LCD
It is on when adjusting the VOX level
It is on when adjusting the vibration function on and off
It is on during registration
It is on when selecting Camera
4 Getting started
4.1 Baby unit battery Installation
The camera uses either 4 x AAA- Size batteries (alkaline batteries recommended) or the mains supply.
1. Loosen the screw in a counter-clockwise direction using a small screw driver. Remove the battery cover.
2. Install 4 'AAA' alkaline batteries by following the polarity as shown in the compartment. Close the battery compartment
and tighten the screw in clockwise.
3. Slide the Power switch to ON position. The Power LED should light up.
Slide the Power switch to OFF position to turn off the baby unit.
When the LED light flashes slowly, the batteries are low and needs to be replaced.
Remark: The Baby unit has no charging function.
IMPORTANT
Install first the 4xAAA size battery before plugging the AC power supply.
4.2 Baby unit power supply
1. Connect the small plug of the AC adaptor to the Baby unit and the other end of the adapter cable to the electric socket.
2. Slide the Power switch to the ON position. The Power LED should light up.
Slide the Power switch to OFF position to turn off the baby unit.
4.3 Parent unit battery Installation
1. Loosen the screw in a counter clockwise direction using a small screw driver. Remove the battery cover.
2. Plug the rechargeable battery pack paying attention to the polarity orientation in the compartment. Close the battery
compartment.
3. Press and hold the Power button (6) to turn ON the parent unit.
(When unit is powered up with either AC power or Rechargeable battery, the LED will light in green color. If both AC
power and rechargeable battery are used, it will light in red color.)
Press and hold the Power button (6) to turn OFF the parent unit.
When the battery charge turns low, the LED light will flash. The battery pack needs to be charge.
Note: When the parent unit turns on, it will take a few seconds to initialize the system and the screen will show the logo
page.
Remark:
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit & dispose of in fire.
Remove the batteries if this device is not going to be used for a long period.
4.4 Parent unit power supply
1. Connect the small plug of the AC adaptor to the parent unit and the other end of the adapter cable to the electric
socket
2. Press and hold the Power button to turn ON the parent unit. The Power LED should light up green.
Press and hold the Power button to turn OFF the parent unit.
Once the Baby unit and Parent Unit have been switched on, the display of the parent unit will show the captured video
from the Baby unit.
5 Using the Baby Monitor
5.1 Fine tuning
• Place the camera in a convenient location, point the lens of the camera to the observation area.
• Move the head of the baby unit up or down to your desired position and ensure the parent unit has good reception of
the baby.
Do not place the camera within the babies reach!
5.2 Night vision
The camera has high-intensity LED's for picking up clear images in the dark. When the built in photo sensor measures
the ambient light level as low, the LED's will automatically activate and it will show black and white screen.
5.3 Melody function
You can remotely activate a melody to be played on the baby-unit.
• Press Play/Pause button (1) once to start the melody playback. Press this button again to pause the melody playback.
• During Melody playback, press Melody Select button (2) to select the melody. You can select;
! or !1, !2, !3, !4 and !5. Selecting ! will play back all melodies sequentially.
Selecting others will play back individual melody.
• In the first 10 seconds of melody playback, pressing Up (3) or Down (4) button can adjust the melody volume in baby
side.
Note: After this 10 seconds, pressing Up (3) or Down (4) button will adjust the volume of the parent unit.
5 4 Talk back function