Technical Data; English; Sander Safety Warnings; Mains Connection - AEG FS250 Manual Original

English

TECHNICAL DATA

Oscillating sander
Production code
Rated input
Voltage
No-load speed
Orbital travel diameter
Dimensions of grinding plate
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 62841. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) 76 dB(A)
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
GB
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN 62841
Vibration emission value a
Uncertainty K=
WARNING!
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with
another.It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for diffe-
rent applications, with different accessories or poorly maintained,
the vibration and noise emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi-
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING!
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow
all instructions listed below may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future reference.
English
8
FS250
4770 49 01...
... 000001-999999
250 W
220-240V AC
50/60Hz
6000-12000 min
2,0 mm
90x187 mm
1,8 kg
87 dB(A)
5,5 m/s
2
h
1,5 m/s
2

SANDER SAFETY WARNINGS

Wear ear protectors. Exposure to noise can cause hearing loss.
Appliances used at many different locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Make sure the machine is switched off before plugging in.
-1
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
This machine is suitable only for dry sanding.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
Do not reach into the machine while it is running.
Chips and splinters must not be removed while the machine is
running.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g.
asbestos).
When grinding metal, flying sparks are produced. Take care that
no persons are endangered. Because of the danger of fire, no
combustible materials should be located in the vicinity (spark flight
zone). Do not use dust extraction.
Do not let any metal parts enter the airing slots - danger of short
circuit!

MAINS CONNECTION

Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
Only plug-in when machine is switched off.
SPECIFIED CONDITIONS OF USE
The oscillating sander can be used for sanding wood, plastics and
metal.