Lutron Skylark S2-L Manual De Instrucciones

Incandescent Dual Dimmer
S2-L, S2W-L
Rated at 120 V~ 60 Hz 600 W (300 W per circuit)
Purchase wallplate separately.
Important Notes
Please read before installing.
1. CAUTION: To avoid overheating and possible damage to other equipment,
do not use to control receptacles, fl uorescent lighting fi xtures, or transformer-
supplied appliances.
2. Dimmer requires separate wires in the wallbox for each light circuit.
3. When no "grounding means" exist within the wall box the NEC
404-9 allows a dimmer without a grounding connections to be installed as a
replacement as long as a plastic, noncombustible wallplate is used. For this
type of installation, cap or remove the green ground wire on the dimmer and
use an appropriate wallplate such as the Lutron's Claro
4. Do not use for lights switched from two locations (3-Way).
5. Use only with permanently installed incandescent or 120 V~ halogen fi xtures.
6. Dimmer may feel warm to the touch during normal operation.
7. For new installations, wire a test switch before installing the control.
8. Install in accordance with all national and local electrical codes.
9. Clean dimmer with a soft damp cloth only. Do not use any chemical
cleaners.
Multi-Unit Installations
When combining controls in a wallbox, remove all inner side sections before wiring (see
below). Use pliers to bend each side section up and down until it breaks off. Repeat for
each side section to be removed. Reduction of dimmer capacity is also required. Refer to
chart below for maximum capacity.
Remove all inner
side sections
(shaded).
Do not remove
outer side
sections.
Model No Sides 1 Side
Number Load Removed Removed
S2-L, S2W-L Incandescent 300 W/300 W 250 W/250 W
Technical Assistance
If you have questions concerning the installation or operation of this product, call the
Lutron Technical Support Center. Please provide exact model number when calling.
1-800-523-9466 (U.S.A., Canada, and the Caribbean)
Other countries call +1-610-282-3800
Fax +1-610-282-3090 Internet: www.lutron.com
Limited Warranty
(Valid only in the U.S.A., Canada, Puerto Rico, the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after
purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg,
PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF
MERCHANTABILITY IS LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE
COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE,
OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL
OR CONSEQUENTIAL DAMAGES. LUTRON'S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR
IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL
NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specifi c legal rights, and you may have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long
an implied warranty may last, so the above limitations may not apply to you.
This product may be covered one or more of the following U.S. patents: 4,835,343; 4,835,816 and
corresponding foreign patents. Lutron, Claro and Skylark are registered trademarks of Lutron Electronics Co.,
Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. © 2006
Lutron Electronics Co., Inc.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in U.S.A. 10/06 P/N 030-487 Rev. C
Lutron Technical Support Center
Installation
For installations involving more than one control in a wallbox, refer to
Multi-Unit Installations before beginning.
Separate wires are required in the wallbox for each light circuit.
Turn power OFF at circuit breaker or remove fuse.
1
For new construction go to Step 5.
2005, Article,
©
2 Remove wallplate. Pull switch from wall.
series wallplates.
®
3 Verify application. This dimmer mounts in a single-gang
wallbox and controls two independent lights, 300 W
maximum for each slider. Independent wire must be
provided for each light.
Tag the wire that is connected to the
feed side of the switch (the side with
the break-off fi n).
Break-off
fi n
2 Sides
Removed
200 W/200 W
4 Disconnect switch wires.
Turn screws to loosen.
5 Prepare wires. Twist and trim wires to the proper length
indicated below when completing Step 6.
Strip length: 3/8" for 14, 16, or 18 gauge.
3/8"
Note: Wire connectors provided are
suitable for copper wire only. For
aluminum wire, consult an electrician.
Use to join the following combinations:
One 14 gauge wire with one 16 or 18
gauge.
1-800-523-9466 24 hrs / 7 days
6
Caution: Verify power
is OFF to switch before
Live
proceeding.
120 V~
120 V
60 Hz
60 Hz
Neutral
7
8
Tag
Operation
Twist wire
connector tight.
Be sure no
bare wire is
exposed.
www.lutron.com
Wire the control:
• Connect the green ground wire
on the dimmer to the green or
Tag
bare copper ground wire in the
wallbox. If there is no ground
Yellow
wire in your wallbox, consult
an electrician.
• Connect the black wire on the
dimmer to the tagged wallbox
wire removed from the switch
(feed wire from breaker panel).
Red
• Connect the red wire on the
Black
Green
dimmer to the wallbox wire
Ground
leading to one of the lights.
• Connect the yellow wire on
the dimmer to the wallbox wire
Black Yellow
leading to the other light.
~
Red
Green
Light
Ground
Light
Mount and align dimmer. Install wallplate.
Start screws. Align control and
tighten screws.
Turn power ON.
LIGHT LIGHT
Bright Bright
Dim Dim
Off Off