Replacement Parts - Shure Microflex MX200 Serie Guia Del Usuario

Ocultar thumbs Ver también para Microflex MX200 Serie:

Guia del usuario (24 páginas)

Guía de usuario (16 páginas)

Guía del usario (16 páginas)

Contenido

página de 17

/ 17
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

MICROPHONE INSTALLATION (Figure 2)

The microphone is most stable when the gooseneck is bent

into a "lazy S" shape as shown in Figure 2. Use the supplied

hanging clip and heavy thread or monofilament fishing line to

suspend the microphone at a specific location.

INSTALLING THE FOAM WINDSCREEN (Figure 3)

1. Press the foam windscreen onto the microphone until it

snaps into the groove located behind the cartridge.

2. To remove the windscreen, spread the gap in its mount-

ing ring with a screwdriver or thumbnail and pull the

windscreen off.

PREAMPLIFIER INSTALLATION

Plate-Mount Preamplifier Input Connections

1. Detach the preamplifier housing by removing the two

Phillips head screws from the back of the housing.

2. Remove the material from the hole in the center of the

cover plate or the center of the preamplifier housing.

3. Cut the cable to the desired hanging length, allowing for

a 76 mm to 101 mm (3 to 4 in.) service loop.

4. Clamp the strain relief around the cable and insert the

strain relief into the hole.

5. Connect the cable leads to the terminal block (B = Black,

R = Red, S = Shield).

Plate–Mount Preamplifier Output Cable Connections

1. Using professional-quality, two-conductor, shielded micro-

phone cable, thread the output cable from the outside of

the preamplifier through the hole with the black bushing.

2. Connect cable to pins as follows: Pin 2 = +, Pin 3 = –,

Shield = S.

3. Reattach the preamplifier housing.

Installing the In-Line Preamplifier (Figure 4)

Use the two supplied mounting clamps to hold the pream-

plifier in place on a wall or ceiling. Set the length of the cable

by cutting it appropriately and using the screw terminal con-

nections inside the preamplifier. The terminals are marked

B (black), R (red), and S (shield).

Adjusting Preamp Gain (Figure 5)

This MX microphone includes an adjustable gain preamplifi-

er, allowing the user to specify a 12 dB or 0 dB gain setting. The

preamp ships at the 12dB setting. Gain may be decreased by

12dB by moving the preamp jumpers to the 0dB setting.

SPECIFICATIONS

Frequency Response (Figure 9)

50 to 17,000 Hz

Polar Pattern (Figure 10)

Output Impedance

180 Ω actual (EIA rated at 150 Ω)

Sensitivity (At 1,000 Hz, open circuit voltage*)

Cardioid:

–35.0 dBV/Pa (17.8 mV)

Supercardioid:

–33.5 dBV/Pa (21.1 mV)

Omnidirectional: –27.5 dBV/Pa (42.2 mV)

All values –12 dB at 0 gain

*1 Pascal = 94 dB SPL

Maximum SPL (1 kHz at 1% THD, 1 kΩ load)

Cardioid:

124.2 dB

Supercardioid: 122.7 dB

Omnidirectional: 116.7 dB

All values +6 dB at 0 gain

Equivalent Output Noise (A-weighted)

Cardioid:

28.0 dB SPL

Supercardioid: 26.5 dB SPL

Omnidirectional: 20.5 dB SPL

Signal to Noise Ratio (referenced at 94 dB SPL)

Cardioid:

66.0 dB

Supercardioid: 67.5 dB

Omnidirectional: 73.5 dB

Dynamic Range at 1 kΩ Load

96.2 dB

100 dB at 0 gain

Common Mode Rejection

45.0 dB minimum

Preamplifier Output Clipping Level (1% THD)

–6.0 dBV (0.5 V)

–12 dBV at 0 gain

Polarity

Positive sound pressure on diaphragm produces positive

voltage on pin 2 relative to pin 3 of output connector.

Power Requirements

11 to 52 Vdc phantom, 2.0 mA

Environmental Requirements

Operating Temperature Range: –18° C to 57° C (0° F to

135° F)

Relative Humidity: 0 to 95%

Dimensions (Figure 7)

CERTIFICATION

Eligible to bear CE Marking. Conforms to European EMC

Directive 89/336/EEC. Meets applicable tests and perfor-

mance criteria in European Standard EN55103 (1996) parts

1 and 2, for residential (E1) and light industrial (E2) environ-

ments.

NOTE: For technical data by fax, phone 1-800-488-3297

and follow the recorded instructions. For additional techni-

cal assistance, phone Shure at (847) 866-2200. In Europe,

phone 49-7131-72140.

Shure, the Shure logo, and Microflex

marks of Shure Incorporated.