Klein Tools 93PLL Manual De Instrucciones página 4

ENGLISH
OPERATING INSTRUCTIONS
TURNING LASER BEAMS ON/OFF
Push the ON/OFF buttons for the X-Plane
turn ON and OFF their respective laser lines. These buttons are only active once the
Pendulum Lock/Unlock Slider Switch
Pendulum Slider Switch is moved from the Unlocked to the Locked position while the
laser beams are active, they will be turned OFF. The different laser lines can be operated
independently or simultaneously.
X-Plane Laser Line Y-Plane Laser Line
NOTE: The plumb spot can be found by locating the top and bottom laser line
intersections while projecting both Y-Plane and Z-Plane Laser lines simultaneously. The
bottom laser line intersection can be used to locate a specific point on a floor layout
while the top laser line intersection projects that same point to a ceiling.
PENDULUM SLIDER SWITCH & SELF-LEVELING
The laser assemblies are mounted on a pendulum so that the instrument can self-level.
10
The Pendulum Slider Switch must be in the unlocked position for the instrument to
self-level. If the instrument is tilted by >4° from the horizontal plane, the pendulum will
not be capable of self-leveling; the active laser beams will flash and the Excessive Tilt
4
Indicator will blink to indicate that the instrument is not level and cannot self-level.
The instrument must be repositioned on a more level geometry for the self-leveling
pendulum to function appropriately.
NOTE: If the instrument indicates that it is not level
(via flashing beams and/or a blinking Excessive Tilt
indicator
out level or plumb lines.
NOTE: Following use, the active laser beams must be
turned OFF and the Pendulum Slider Switch must be
placed in the Locked position prior to storage.
Instrument Tilted Excessively
6
1 2
, Y-Plane , and Z-Plane 3
10 has been set to the Unlocked position. If the
Z-Plane Laser Line
4 ), then it should not be used for laying
MAGNETIC MOUNTING BRACKET
A magnetic mounting bracket is included with the product. The instrument can be
lines to
mounted on the bracket via its 1/4" threaded screw
attached to any ferrous structure such as steel studs, ducts, structural beams, and steel
doors. The bracket also feature a keyhole for mounting the instrument using a screw or
nail to non-ferrous structures. Once mounted to a structure via the mounting bracket, the
instrument can be rotated on the bracket through 360° to direct the laser beams.
When the Red LED on the Battery Level Indicator blinks, the battery needs to be recharged:
Charging Battery via 93PLL USB-C Port:
1. Connect supplied charging cable's
the 93PLL.
2. Connect the charging cable's USB-A port to a charging source (5V DC, Min 2.0A, not
included).
3. The Battery Level Indicator
4. A full charge can take up to 8.5 hours, depending on the charger's output. Charge
completely before using.
Charging Battery via Battery Pack
USB-C Port:
1. Ensure 93PLL is turned off by
locking the Power/Pendulum
Switch 10 .
2. Loosen screw from the Battery
Door 12 and remove battery.
3. Connect the supplied charging
cable's 13 USB-C connection to
battery's Charge-In Port
4. Connect the charging cable's
USB-A port to a charging source
(5.0V, min. 2.0A, not included).
5. Battery Charge Indicator LED
17 will blink red while charging,
and turn solid green when fully
charged. When fully charged,
disconnect cable from battery
and reinstall battery in 93PLL.
6. Close the battery door and secure with screw. Do not over-tighten.
OPERATING INSTRUCTIONS
14
15
. The bracket may be magnetically
RECHARGING BATTERY
13 USB-C connection to the USB-C port
5 will illuminate to indicate charging status (TABLE 1).
TABLE 1
Not
Green Yellow
Illuminated
LED Status
Solid green
Solid green
Solid yellow
Solid red
Blinking green
Solid green
Solid yellow
Solid red
16
.
Blinking green
Blinking green
Solid yellow
Solid red
Blinking green
Blinking green
Blinking yellow
Solid red
Blinking green
Blinking green
Blinking yellow
Blinking red
6 of
Red Blinking
% Charged
100% charged
75% to 99% charged
50% to 74% charged
25% to 49% charged
0% to 24% charged
7