Spindle Lock Button - Worx WX700 Manual De Instrucciones

OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for cutting,
roughing and brushing metal and stone
materials without using water. For cutting
metal, a special protection guard for cutting
(accessory) must be used.
1. INSTALLING THE AUxILIARy HANDLE
(See Fig. A)
You have the option of two working positions
to provide the safest and most comfortable
control of your angle grinder. The handle is
screwed clockwise into either hole on the
sides of the gear case.
Anti-vibration auxiliary handle (Wx707
Wx707.1)
The anti-vibration auxiliary handle reduces
the vibrations, making operation more
comfortable and secure.
2. ADjUSTING WHEEL GUARD (See Fig. b)
12
before any work on the machine itself,
pull the mains plug.
For work with grinding or cutting discs,
the wheel guard must be mounted.
Wheel Guard for Grinding
The coded projection on the wheel guard (10)
ensures that only a guard that fits the machine
type can be mounted.
Open the clamping lever (9). Place the wheel
guard (10) with coded projection into the
coded groove on the spindle of the machine
head and rotate to the required position
(working position).
To fasten the wheel guard (10), close the
clamping lever (9).
The closed side of the wheel guard (10)
must always point to the operator.
NOTE: With the clamping lever (9) open the
clamp adjusting nut (7) can be adjusted to
ensure the guard is securely clamped after the
clamping lever (9) is finally closed.
Wheel Guard for cutting
WARNING! For cutting metal,always
work with the wheel guard for cutting(12).
The wheel guard for cutting (12) is mounted
Angle grinder
All manuals and user guides at all-guides.com
in the same manner as the wheel guard for
grinding(10) .

3. SPINDLE LOcK bUTTON

Clean the grinder spindle and all parts to be
mounted. For clamping and loosening the
grinding tools, lock the grinder spindle with
the spindle lock button.
Actuate the spindle lock button only when the
grinder spindle is at a standstill!
4. FITTING THE DIScS (See Fig. c1, c2, c3)
Put the inner flange onto the tool spindle. Ensure it
is located on the two flats of spindle (See Fig. C1).
Place the disc on the tool spindle and inner
flange. Ensure it is correctly located. Fit the
threaded outer flange making sure it is facing in
the correct direction for the type of disc fitted.
For grinding discs, the flange is fitted with the
raised portion facing towards the disc. For
cutting discs, the flange is fitted with the raised
portion facing away from the disc (See Fig. C2).
Press in the spindle lock button and rotate the
spindle by hand until it is locked. Keeping the
lock button pressed in, tighten the outer flange
with the spanner provided. (See Fig. C3)
USING INSTALOcK
(Wx701.2 Wx702.1 Wx707.1)
Lock the grinder spindle with the spindle lock
button. To tighten the INSTALOCK
Flange (13) firmly turn the grinding disc in
clockwise direction.
A properly attached, undamaged INSTALOCK
tool-less Flange can be loosened by hand
when turning the knurled ring in anti-clockwise
direction. Never loosen a tight INSTALOCK
tool-less Flange with pliers. Always use the
two-pin spanner.
5. SLIDE ON/OFF SWITcH (See Fig. D)
To start the power tool, push the on/off switch
(2) forward.
To lock the on/off switch (2), press the on/off
switch (2) down at the front until it engages.
To switch off the power tool, release the on/off
switch (2) or, if it is locked, briefly push down
the back of the on/off switch (2) and then
release it.
®
TOOL-LESS FLANGE
®
tool-less
®
EN
®