General Settings; Warnings; Power; Safety Precautions - Urmet 1093 Guía Rápida De Configuración

1

GENERAL SETTINGS

Dear Customer,
Thank you for having purchased this Urmet product.
This document is a simple, quick reference guide to help you start up the NVR URMET S.p.A. Ref. 1093/900.
NOTE
For more detailed information about the devices, refer to the full instruction manual inside the CD provided with the
product.
1.1

WARNINGS

1.1.1

POWER

Check mains rating before plugging the power unit in.
Do not pull the cable to unplug the device.
Switch the device off before unplugging power unit. This operation must not be performed when the NVR is
recording, playing or from the configuration menu. Stop recordings and playback in progress before
disconnecting power from the device to prevent damaging the hard disk beyond repair.
1.1.2

SAFETY PRECAUTIONS

Keep the device away from rain and humidity to prevent risk of fire and electrocution. Do not introduce material
(solid or liquid) inside. If this should accidentally occur, disconnect the device from the mains and have it
inspected by qualified personnel.
Never open the device. In all cases, contact a qualified personnel or authorised service centre for repairs.
Keep the device away from children, to prevent accidental damage.
Do not touch the device with wet hands to prevent electrical shock or mechanical damage.
Do not use the device if it should fall or the external casing is damaged. Risk of electrocution if the device is
used in such conditions. Contact the retailer or authorised installer.
1.1.3

INSTALLATION PRECAUTIONS

To prevent overheating the device, arrange it in a position allowing the flow of air through the slots in the casing.
Ensure at least 5 cm of free space when installing inside a rack. For the same reason, do not install sources of
heat, such as radiators or hot air ducts. Keep away from direct sunlight. Do not install in areas subject to
excessive dust, mechanical vibrations or shocks.
Do not arrange this device on an unstable surface, such as a tottering or slanted table. The device could fall
causing injury or mechanical failures.
Do not install the device in a place where it could be exposed to humidity or water. Do not direct a jet of water
onto the device: risk of fire, electrocution or mechanical failure.
Stop using the device if water or other material should penetrate inside: risk of fire and electrocution. Contact
the retailer or authorised installer.
Do not place heavy or heat generating objects on top of the device: this could damage the casing and/or
increase internal temperature causing faults.
Do not cover the device with a cloth while it is running to prevent deforming the external casing and overheating
the internal parts: risk of fire, electrocution and mechanical failure.
Keep magnets and magnetised objects away from the device to prevent faults.
Do not use the device in presence of smoke, vapour, humidity, dust or intense vibrations.
Wait for a while before operating a device immediately after transporting it from a cold place to a warm place
and vice versa. Wait on average for three hours: this will allow the device to adapt to the new ambient
(temperature, humidity, etc.).
1.1.4

CLEANING THE DEVICE

Rub delicately with a dry cloth to remove dust and dirt.
Dip the cloth in neutral detergent if dirt cannot be eliminated with a dry cloth alone.
Do not use volatile liquids (such as petrol, alcohol, solvents, etc.) or chemically treated clothes to clean the
device to prevent deformation, deterioration or scratches to the paint finish.
1.1.5

HARD DISK

The hard disk installed in this device is sensitive to shocks, differences in temperature and vibrations.
Disrespect of these precautions can compromise correct operation of the device and cause loss of data stored
on the hard disk.
If repairs are required, it is advisable to backup all important data before taking the device to the service centre.
URMET S.p.A. is not liable for loss of stored data.
The addition of a hard disk must be performed by qualified technical personnel or by contacting the technical
assistance service.
1.1.6

IMAGE RECORDING

This device was designed to record images, not as a burglar alarm. URMET S.p.A. cannot be held liable for loss
or damage following theft sustained by the user.
Make a test recording before using the device to make sure that is working correctly. Please note that URMET
S.p.A. is not liable for loss of stored data consequent to loss or damage caused by incorrect observation
installation, use, improper use or malfunctioning of the device.
DS1093-155A 25