3M DBI-SALA FLEXIGUARD M100 Manual De Instrucciones página 7

;
Before using this equipment, record the product identification information from the ID label into the inspection and
maintenance log of this manual.
;
This Floor Mount Base can only be used with the 3M Modular Jib System M100 manufactured by 3M. Do not attempt to use
the Floor Mount Base without first consulting the user instruction 5908371 for the 3M Modular Jib System M100.
System Specifications:
Compatability:
Standards:
Capacity:
Dimensions:
Maximum Deflection:
Maximum Arresting
Force:
Weight:
Component Specifications:
Component
General Construction
Structural Material
Base Finish
8530918 Base Cap
Mounting Requirements:
Model Minimum Fastener Pullout
Number Force
8530871 5,744 lb. (2,606 kg)
8530872
8530918
; See the fastener manufacturer's specifications for fastener requirements.
1.0 PRODUCT APPLICATION
1.1 PURPOSE: The Floor Mount Base is designed for use as a component of a Fall Protection system.
1.2 DESCRIPTION: The Floor Mount Base (Figure 1)
point for the 3M approved Modular Jib System M100.
1.3 STANDARDS: The Floor Mount Base conforms to the national or regional standard(s) identified on the front cover of these
instructions. If the product is resold outside of the original country of destination, the re-seller must provide these instructions in
the language of the country in which the product will be used.
1.4 SUPERVISION: Installation of this equipment must be supervised by a Qualified Person
supervised by a Competent Person
1.5 TRAINING: This equipment must be installed and used by persons trained in its correct application. This manual is to be
used as part of an employee training program as required by national, regional, or local standards. It is the responsibility
of users and installers of this equipment to ensure they are familiar with these instructions, trained in the correct care
and use of this equipment, and are aware of the operating characteristics, application limitations, and consequences of
improper use of this equipment.
1 Qualified Person:
A person with a recognized degree, certificate, or professional standing, or who by extensive knowledge, training, and
experience has successfully demonstrated their ability to solve or resolve problems relating to fall protection and rescue systems to the extent
required by applicable national, regional, and local regulations.
2 Competent Person:
One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are
unsanitary, hazardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
Table 1 – Specifications
The Floor Mount Bases covered in this instruction are compatible with 3M™ DBI-SALA®
Flexiguard™ Modular Jib System M100.
Designed to meet the test requirements of EN795:2012 (Type A), OSHA 1926.502, and OSHA
1910.140.
See 3M™ DBI-SALA® Flexiguard™ Modular Jib System M100 instruction 5908371.
See Figure 1 for dimensions of the Floor Mount Base.
Refer to the instruction manual for the M100 Jib Boom (5908371) for more information on
maximum system deflection.
All connecting subsystems (SRDs, Energy-Absorbing Lanyards, etc.) used with the Floor Mount
Base must limit the Maximum Arresting Force to 1,350 lbf. (6 kN).
8530871: 203 lb. (92 kg)
8530872: 315 lb. (143 kg)
8530918: 91 lb. (41 kg)
8530919: 224 lb. (102 kg)
Material
Welded Steel
A36 Steel
8530871 - Powdercoat
8530872 - Zinc Plating, Powdercoat
8530918 - Zinc Plating
8530919 - Powdercoat
Aluminum, Stainless Steel Ring, Rubber Gasket
Mounting Structure Minimum
Moment Load
is designed to be anchored to approved structures and used as a mounting
.
2
255,474 in-lb. (28,865 N-m)
255,474 in-lb. (28,865 N-m)
7
Mounting Structure Minimum
Vertical Load
2,700 lb. (1,225 kg) + Base Weight
+ Jib Weight
2,700 lb. (1,225 kg) + Base Weight
+ Jib Weight
. Use of this equipment must be
1