Good Earth Lighting SE1216-BRS-02LF4-G Manual De Instrucciones página 2

MOTION SENSOR
Extreme hot or cold weather could affect the performance of the built-in sensors that detect body heat. Certain winter clothing can shield a person's body
heat from the sensor during extreme cold weather. During extreme hot weather, the sensor may not be able to distinguish the difference between normal
body temperatures and the surrounding high temperatures. The sensor will begin working normally once weather conditions return to normal.
CARE AND MAINTENANCE
Periodically clean the fixture using a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. Spray liquid cleaner onto cloth and wipe
fixture clean.
Troubleshooting Guide
PROBLEM
Security light 1. ON/OFF switch is not set correctly.
does not come on.
2. Batteries are defective or depleted.
3 Batteries are installed wrong.
4. Battery compartment cover is loose.
5. It is daylight.
6. Movement is taking place outside of the motion sensor detection area.
Light continuously 1. Light sensor is triggered by reflected light from the security light itself.
cycles ON and OFF
2. Heat is being reflected from other sources and may be triggering sensor
(strobe effect).
on and off.
Light turns on during 1. Light may be installed in shadows/dark area.
daylight hours.
Light comes on for no 1. Sensor may be triggered by a small animal or passing car.
apparent reason.
2. Hot air (dryer vent, car exhaust, etc.) may be triggering the sensor.
Light stays on 1. Motion sensor may be picking up a continuous flow of warm air from an
continuously. air vent, dryer vent or heat reflecting off a surface.
REPLACEMENT PARTS LIST
FCC Statement: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
- 3 YEAR LIMITED WARRANTY: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (3) years from the date of original
Good Earth Lighting ®
purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the
unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the
manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your
defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be
liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to
person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to
the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Need Help?
1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting
®
Good Earth Lighting is a registered trademark of Good Earth Lighting, Inc. © 2019 Good Earth Lighting, Inc.
®
1. Les DEL peuvent être endommagées par une décharge électrostatique (DES). Avant l'installation, déchargez-vous en touchant une surface en
métal nue mise à la terre pour éliminer un tel risque. Pour éviter tout endommagement, ne retirez pas la lentille transparente qui recouvre le
module de DEL.
2. NE LE MONTEZ PAS SUR UN AVANT-TOIT SUR UN MATÉRIAU D'AVANT-TOIT PERFORÉ. Ceci pourrait permettre à l'eau de s'infiltrer à travers la
monture du luminaire.
INSTRUCTIONS POUR LE MONTAGE
Retirez la plaque de montage en tournant dans le sens contraire des aiguilles d'une montre jusqu'à ce qu'elle se desserre.
Localisez les orifices ouverts en vue du montage sur la ligne médiane de la plaque de montage et percez un trou pilote au centre. En cas de montage sur de la brique ou de la maçonnerie, percez un
trou de 0,48 cm et placer les ancrages de maçonnerie (AA) dans les trous pilotes, puis enfoncez-les jusqu'à ce qu'ils soient alignés avec la surface de la maçonnerie. Enfoncez les vis longues (BB)
dans les ancrages de maçonnerie jusqu'à ce qu'elles soient bien en place. NE SERREZ PAS EXCESSIVEMENT. En cas de montage sur une surface en bois, utilisez les vis à bois (BB) fournies afin de
fixer la plaque de montage.
MOTION SENSOR
The light turns on when the motion sensor detects movement. Sensor detects motion up to 40ft.
The 180-degree coverage of the motion sensor is measured side-to-side. The sensor is more
effective side-to-side, rather than motion coming straight at it (in-and-out). Fixed timer is 15
seconds – lights will stay on for 15 seconds after motion detection (only during night hours).
POSSIBLE CAUSE
Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
AVERTISSEMENTS ET MISES EN GARDE
MAÇONNERIE
AA
x2
BB
x2
1. Slide switch to ON position.
2. Replace the batteries.
3. Reinstall the batteries correctly.
4. Check battery compartment cover to ensure it is closed and secured with the screw.
5. Light is operating as it was designed. Recheck at night or move fixture to a darker area.
6. Move fixture within the desired detection area.
1. Change the position of the light heads, aiming light away from the reflecting surfaces.
2. Remove heat source from detection zone or move fixture to new location.
1. Light is operating as it was designed.
1. Light is operating as it was designed.
2. Remove heat source from detection zone or move fixture to new location.
1. Remove heat source from detection zone or move fixture to new location.
Hardware Kit:
3/16 in.
0,48 cm
foret de
maçonnerie
CORRECTIVE ACTION
ZH-SE1216F02
BOIS
1/16 in.
0,16 cm
180°
Printed in China
2