Fein BF10-280E Serie Manual De Instrucciones página 14

en
14
Character
L
pA
L
wA
L
pCpeak
K...
h
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
Hand-guided belt file for dry sanding and polishing of
metal materials with belts, in weather-protected envi-
ronments using the application tools and accessories
recommended by FEIN.
This power tool is also suitable for use with AC gener-
ators with sufficient power output that correspond to
the Standard ISO 8528, design type G2. This Standard
is particularly not complied with when the so-called dis-
tortion factor exceeds 10 %. When in doubt, please
refer to the generator instruction/specification guide.
Special safety instructions.
Hold the power tool by the insulated gripping surfaces
when performing operations where the application tool
could contact hidden wiring or its own power supply
cable. Contact with a "live" wire will also make
exposed metal parts of the tool "live" and shock the
operator.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.
Unit of measure- Unit of measure-
ment, international ment, national
dB dB
dB dB
dB dB
2
m/s m/s
2
m/s m/s
m, s, kg, A, mm, V, m, s, kg, A, mm, V,
W, Hz, N, °C, dB, W, Hz, N, °C, dB,
2
min, m/s min, m/s
Explanation
Sound pressure level
Sound power level
Peak sound pressure level
Uncertainty
2
Vibrational emission value according to
EN 62841 (vector sum of three directions)
2
Vibrational emission value (sanding)
Basic and derived units of measurement from
the international system of units SI.
2
While working, do not wear loose clothing, jewellery or
open, long hair. Despite protective devices, loose
objects can be snagged or caught by moving parts and
lead to injury.
Do not use worn, torn or heavily clogged grinding belts.
Handle grinding belts carefully and store them accord-
ing to the manufacturer's instructions. Do not bend or
fold grinding belts! Damaged grinding belts can tear, be
flung away and injure someone.
Never touch the running grinding belt and do not reach
under the protective guard. Danger of injury.
Secure the work piece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
Hold the power tool firmly. High reaction torque can
briefly occur.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not use accessories which are not specifically
designed and recommended by the power tool manu-
facturer. Safe operation is not ensured merely because
an accessory fits your power tool.
Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connec-
tion and the mains plug for damage.
Recommendation: The tool should always be supplied
with power via a residual current device (RCD) with a
rated current of 30 mA or less.
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth