Craftsman CMEED400 Manual De Instructiones página 9

nOTE: The edger is a major appliance and should not be
operated simultaneously with other major appliances on
the same household circuit.
Usage
1. Set cut depth at 1 " and set edge guide to
the down position, refer to Assembly and
Adjustments Instructions.
2. Before starting the edger, line up the tool so the edge
guide rests against the edge of the paved surface.
Both rear wheels should be on the paved surface
when edging.
nOTE: When there is heavy overgrowth of grass over the
paved surface it may drag on the guard. An initial cut may
be required with the edger on the grass side. This will
require lifting up the edge guide and may require reducing
the depth of cut (refer to To Change Position of the Edge
Guide instructions).
3. To avoid kickback of edger, tilt the handle down so the
blade is above the ground.
4. Turn switch ON and allow blade to spin without
moving tool.
5. Slowly lift the handle to lower the blade, finding the
edge of the paved surface and start edging. Then
move tool forward slowly along edge of paved surface,
keeping the edge guide pressed lightly against the
pavement edge.
- For the first edging each season, it is best to move
forward slowly because grass is thickest then.
Subsequent edging will be completed more rapidly.
If the tool slows down, back it up an inch or two
until the blade comes up to normal speed. During
edging some sparks may be generated from hitting
stones. This is normal. Do not attempt to edge when
the grass or soil is wet or moist—for electrical safety
and to prevent clogging of the blade chamber. If
you must edge under conditions that cause the
blade chamber to become clogged, release trigger,
wait for blade to come to complete stop. Unplug
tool, open door and remove clogged material with
a stick. To continue to operate the tool in a clogged
condition will seriously overload the motor.

CAUTION:
blade chamber by dropping or tapping the tool on the
ground. This can damage the unit. Keep hands clear of
edge guide and blade when cleaning as these wear to
a very sharp point during edging.
Landscaping/Trenching

WARNING:
Trenching, inspect and ensure there are no exposed or
buried cables, pipes or other objects that may create a
hazard or interfere with operating the edger. Set depth
to only that required for the job. Do not overload.
If tool slows, pull back slightly and wait until blade
comes up to normal speed.
Do not attempt to unclog the
Before Landscaping or
Storage

WARNING:
Remove and clean any debris from the outside of the edger
and inside of guard before storage. Refer to MAINTENANCE
section. If necessary, the edger may be stored by hanging
on a hook by its handle.

CAUTION:
switch trigger or power cord.
NOTICE:
to fertilizers or chemicals. Such storage can cause
rapid corrosion.
Preventing Corrosion
Fertilizers and other garden chemicals contain agents that
greatly accelerate the corrosion of metals. If you use the
tool in areas where fertilizers or chemicals have been used,
the tool should be cleaned immediately afterwards. Wipe
all exposed parts with a damp cloth. You may lubricate only
metal parts with a light petroleum based oil.
When cleaning, DO NOT immerse tool in water or squirt it
with a hose.
MAINTENANCE

WARNING:
serious personal injury, turn unit off and
disconnect it from power source before making
any adjustments or removing/installing
attachments or accessories. An accidental start-up
can cause injury.
Cleaning

WARNING:
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING:
harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING:
those offered by CRAFTSMAN, have not been tested
Be sure the tool is unplugged.
Do not hang edger on the
Do not store the tool on or adjacent
To reduce the risk of
Blow dirt and dust out
Never use solvents or other
Since accessories, other than
English
7