Installation Instructions; Part Numbers - Cequent Performance Products 75790 Instrucciones De Instalación

Frame rail
Rearward
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75790F (May have fasteners left over.)
Wrenches: 11/16", 19 mm
Vehicle shown
without existing weld
nuts.
Note: 19mm open end style wrench
must be purchased to allow
removal of spare tire after
hitch installation.
j
Conical Washer 1/2"
Qty. (4)
k
Qty. (3) Hex Bolt M12 x 1.75 mm x 45 mm CL 10.9
l
Carriage Bolt 7/16"-14 x 1-3/4" GR 5
Qty. (4)
m
Block 3/16" x 1" x 2"
Qty. (4)
n
Conical Washer 7/16"
Qty. (4)
Install blocks and 7/16" carriage bolts using the pull wire procedure as shown. Leave the pull wires attached.
1.
2. Position the hitch on the frame rail as shown.
Use the pull wires to insert the 7/16" carriage bolts through the attachment holes of the hitch. Remove the pull wires.
3.
Install the 7/16" conical washers and hex nuts as shown.
4.
5. Insert nut-block-handle assembly through opening in rear of frame rail and slide over rearmost hole (both sides). Make sure each
nut-block-handle assembly is flat on the surface of the frame rail.
While holding the nut-block-handle assemblies in place, install M12 x 1.25 mm hex bolts and 1/2" conical washers as shown.
6.
7. Torque all fasteners to specification.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent
entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a
vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and
SAE J684.
© 2013 Cequent Performance Products, Inc.
Printed in Mexico

Installation Instructions

Note: Relocation of spare tire bracket is NOT required.
Fascia
Frame rail
Note: Fasteners typical both sides
Tighten all 7/16" GR 5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Tighten all M12 x 1.75 mm CL 10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Tighten all M12 x 1.25 mm CL 10.9 fasteners with torque wrench to 130 Lb.-Ft. (176 N*M)
Ford Ranger
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU3 & PU4
Existing hole
Example of Pull Wire Procedure
q
j
r
o
Hex Nut 7/16"-14
Qty. (4)
p
Pull Wire 7/16"-14
Qty. (4)
q
Qty. (2) Nut-Block-Handle Assembly
r
Qty. (2) Hex Bolt M12 x 1.25 mm x 40 mm CL 10.9
Sheet 2 of 6 75790N

Part Numbers:

Manufacturer's Rating or
Max Gross
Trailer WT (LB)
6,000 (2724 Kg)
4,000 (1816 Kg)
Accessory Rating
Kink pull wire to keep block
independent of bolt
p
Frame rail
09-03-13
Form: F205 Rev C 9-17-2012
75790
Max Tongue
WT (LB)
600 (272 Kg)
600 (272 Kg)
C
l
m
n
o
Rev. B