Noise/Vibration Information; Intended Use - EDM Product 08766 Manual De Instrucciones

Angle grinder
Safety Warnings
supplied with
the charger. Any other use may result in the risk of fire,
electric shock or electrocution.
The charger and battery pack supplied with it are
specifically designed to work together. Do not attempt to
charge the battery pack with any other charger than the
one supplied.
Do not place any object on top of the charger as it could
cause overheating. Do not place the charger near
any heat source.
Pull on the charger to disconnect it from the power source.
Do not pull on the lead.
Make sure that the charger lead is positioned where it will
not be stepped on, tripped over or otherwise subjected to
damage or stress.
Do not use an extension cord unless it is absolutely
necessary. The use of an improper extension cord could
cause the risk of fire, electric shock or electrocution.
Do not use the charger if it has been subjected to a heavy
knock, dropped or otherwise damaged in any way. Take the
charger to an authorized service centre for a check or repair.
Do not disassemble the charger. Take it to an authorized
service centre when service or repair is required. Incorrect
re-assembly may result in the risk of fire, electric shock or
electrocution. To reduce the risk of an electric shock, unplug
the charger from the power supply before attempting to
clean it. Removing the battery pack alone does not reduce
the risk. The charger is designed for use from a standard
household electrical supply. Do not attempt to connect the
charger to a supply with a different voltage.
The charger is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the charger by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the charger. Do not expose charger to rain or
snow.
Do not mount charger on wall or permanently affix charger
to any surface. The charger is intended to use
on a flat, stable surface(i.e. table top, bench top) Never
attempt to connect two chargers together.
Never insert any objects into the charger's air vents. Electric
shock or damage to the battery charger may result.
Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce this risk.
Never recharger a fully charged battery cartridge. Do not
charge non-rechargeable batteries.

Intended use

The machine is intended for lengthways and crossways
cutting of wood with straight cutting lines as well as mitre
WARNING: Do not allow any liquid to come into contact with the charger.
There is a danger of electric shock.
EN
cuts in wood while resting firmly on the workpiece.
With suitable saw blades,
metals,e.g.,profiles, can also be sawed.
Working ferrous metals is not permitted.

Noise/vibration information

Measured sound values determined according to EN
60745-1.
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745-1: The vibration emission level given
in this information sheet has been measured in accordance
with a standardized test given in EN60745-1 and may be
used to compare one tool with another. It may be used for a
preliminary assessment of exposure. The declared vibration
emission level represents the main applications of the tool.
However, if the tool is used for different applications, with
different accessories or poorly maintained, the vibration
emission may differ. This may significantly increase the
exposure level over the total working period. An estimation
of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is
running but not actually doing the job. This may
significantly reduce the exposure level over the total
working period. Identify additional safety measures to
protect the operator from the effects of vibration, such as
maintaining the tool and the accessories, keeping hands
warm, adjusting work patterns to avoid risk of vibration.
Vibration risk limitation suggestions:
1) wear glove during operation
2) limit operating time and shorten trigger time.
thin-walled non-ferrous