Setting Of The Battery Check Card; Hour Meter; Squeegee Assembly; Adjustment Of The Squeegee - ADIATEK coral 70s Uso Y Mantenimiento

GB
ATTENTION:
When the indication -10- appears blinking, auto-
matically the brushes stop, while the suction contin-
ues to work. When visualizing the four lines blinking,
also the suction will stop automatically. Instead, the
traction system remains functioning to enable the
transfer of the machine to the place provided for the
tank emptying and for the recharge of the batteries.

SETTING OF THE BATTERY CHECK CARD

The setting of the battery check card can be:
GE 24 (check card set for GEL batteries).
or
Pb 24 (check card set for lead batteries).
The machine, if not specified otherwise, is supplied
with the battery check card set for lead batteries. To
modify this setting, it is necessary to:
1. Switch off and on the machine.
2. Immediately after having switched on, when on
the display (1) the writing Pb24 appears, press simul-
taneously the push buttons (3) and (6) up to the
blinking of the writing.
3. When the writing begins to blink, take off the
fingers from the push buttons and press once the
push button (6).
4. The writing GE24 appears blinking.
5. When the writing stops to blink, the setting is
modified.
For the passage of the setting from gel batteries into
lead batteries, repeat the procedure pressing button
(3) instead of button (6).
ATTENTION:
As the machine is a 24V model, do not set the bat-
teries at 36V.

HOUR METER

The machine is equipped with an hour meter located
on the same display (1) of the battery charge level
indicator. Keeping the button (13) pressed, the first
data indicates the working hours and after a few se-
conds the working minutes are shown.

SQUEEGEE ASSEMBLY

1. Maintain the squeegee support (1) slightly lifted
from the floor.
2. Insert the threaded parts of the two knobs (4)
making them slide inside the two slots on the sup-
port placed on the upper part of the squeegee (2).
3. Put the washers (3) into position, they are two
for each knob, so that they are assembled one under
and the other on each of the two slots present on
the support.
4. Block the squeegee by rotating the two knobs (4)
clockwise.
5. Insert the squeegee hose (5) into its coupling, re-
specting its position as indicated in the figure.

ADJUSTMENT OF THE SQUEEGEE

In order to have a perfect drying result through the
squeegee, the rear rubber must have the lower bend-
ing uniformly adjusted in all its length. For the ad-
justment, it is necessary to put oneself in working
condition and therefore the suction motor has to be
switched on and the brushes have to function to-
gether with the detergent solution.
The lower part of the rubber is too much bent
Take off the pressure rotating the wing nut (6) coun-
terclockwise.
The lower part of the rubber is not much bent
Increase the pressure rotating the wing nut (6)
clockwise. Check that the wheels which adjust the
height do not rest on the floor, in this case adjust
them as indicated in paragraph "Height adjustment".
The bending is not uniform
Adjust the squeegee inclination rotating counter-
clockwise the wing nut (7) to increase the bending in
the central part, or clockwise to increase the bending
on the extremities.
Height adjustment
Once that the pressure and inclination of the squee-
gee have been adjusted, it is necessary to fix this op-
timum condition making touch slightly the wheels
onto the floor. Rotate clockwise the registers (8) to
lower the wheels or counterclockwise to raise them.
Both wheels must be adjusted in the same measure.
23
ATTENTION:
Every type of floor requires a specific adjustment.
For example, concrete floors (where the friction re-
sults to be high) need little pressure, while smooth
floors (ceramics) need higher pressure.
If the cleaning operations are made always on the
same type of floor, the adjustment can change only
in function of the rubber wear.

ADJUSTMENT HEIGHT SIDE RUBBERS

To adjust the side rubbers, it is necessary to act upon
the adjusting screws (1) and (2) after having loos-
ened the upper blocking nuts. Unscrewing, the rub-
ber lowers, while screwing down, the rubber is lifted.
The reason of the adjustment is to obtain an uniform
bending.
Having finished the adjustment, tighten the blocking
nuts to fix the position.

BRUSHES ASSEMBLY AND DISASSEMBLY

Normally, the machine is delivered with the brushes
assembled.
To assemble and disassemble the brushes on both
sides of the machine:
1. Make sure the machine is switched off and with
the brushes base in up position (lifted).
ATTENTION:
To carry out brushes assembly operations with the
electric supply on, may cause damages to hands.
ATTENTION:
This operation must be carried out using gloves to
protect from contact with dangerous solutions.
2. Unblock the bar of the side rubber after having
released the knob (1).
GB