MTD 890 Manual Del Usuario página 20

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 95
INSTALLING AND ADJUSTING THE HANDLEBAR
1. Place the handlebar between the top and middle
clamp pieces (Fig. 1).
2. While holding the three pieces together, install the
four (4) screws through the top clamp and into
middle clamp.
NOTE: The holes in the top and middle clamp will line up
only when assembled correctly.
3. Place the clamps and the handlebar over the shaft
housing and onto the bottom clamp.
4. Hold each hex nut in the bottom clamp recess with a
finger. Start screws with a large Phillips screwdriver.
Do not tighten until you make the handlebar
adjustment.
5. While holding the unit in the operating position
(Fig. 23), position the handlebar to the location that
provides you the best grip.
6. Tighten the clamp screws evenly, until the handlebar
is secure.
INSTALLING AND ADJUSTING THE SHOULDER
HARNESS
Shoulder Harness
1. Loop the strap through the buckle (Fig. 3).
2. Place the harness over the head and the cushioned
pad onto the shoulder.
3. Snap the shoulder harness hook onto the metal
support (Fig. 4). Adjust the length of the harness to a
comfortable position.
Emergency Quick Release
1. For fast release from the unit, pull up on the quick
release tab (Fig. 3)
2. To reasemble the clamp:
a. Place the hook over the release plate (Fig. 5).
b. Insert the pin into the plate (Fig. 6).
OPERATING THE EZ-LINK® SYSTEM
NOTE: To make installing or removing the add-on easier,
place the unit on the ground or on a work bench.
Removing the Cutting Attachment or Add-Ons
1. Turn the knob counterclockwise to loosen (Fig. 7).
2. Press and hold the release button (Fig. 7).
3. While firmly holding the upper shaft tube, pull the
cutting attachment or add-on straight out of the EZ-
Link® coupler (Fig. 8).
20
ASSEMBLY INSTRUCTIONS
Installing the Cutting Attachment or Add-Ons
1. Turn knob counterclockwise to loosen (Fig.7).
2. While firmly holding the add-on, push it straight into
NOTE: Aligning the release button with the guide recess
3. Turn the knob clockwise to tighten (Fig. 9). Ensure it
REMOVING AND INSTALLING CUTTING
ATTACHMENT GUARD
Remove the cutting attachment guard when using the
unit as a brushcutter.
Remove the cutting attachment guard from the guard
mount by removing the three (3) screws with a flat blade
screwdriver (Fig. 10). Store parts for future use.
Install the cutting attachment guard when using the unit
as a grass trimmer.
Install the cutting attachment guard on the guard mount
by inserting the three (3) screws into the guard mount.
Tighten securely with a flat blade screwdriver (Fig. 10).
REMOVING THE CUTTING ATTACHMENT AND
INSTALLING THE CUTTING BLADE
NOTE: To make removing or installing the cutting blade
Remove the Cutting Attachment
1. Align the shaft bushing hole with the locking rod slot
2. Hold the locking rod in place by grasping it next to
3. While holding the locking rod, remove the cutting
Install the Cutting Blade
4. Remove the cutting attachment guard. See
5. Place the cutting blade on the output shaft (Fig. 14).
6. Center the cutting blade on the output shaft bushing
7. Ensure that the cutting blade is centered and sitting
8. Align the shaft bushing hole with the locking rod slot and
9. Put the blade retainer and nut on the output shaft
10. Tighten counterclockwise against the blade while
the EZ-Link® coupler (Fig. 8).
will help installation (Fig. 7).
is tight before operating the unit.
or cutting attachment easier, place the unit on
the ground or on a work bench.
and insert the locking rod into the shaft bushing hole
(Fig. 11).
the shaft tube of the unit (Fig. 12).
attachment by turning it clockwise off of the output
shaft (Fig. 13). Store the cutting attachment for future
use.
Removing and Installing Cutting Attachment Guard.
(Fig. 14).
flat against the output shaft bushing.
insert the locking rod into the bushing hole (Fig. 11).
(Fig. 14). Make sure that the blade is installed
correctly.
holding the locking rod (Fig. 15).
Tabla de contenido
loading

Tabla de contenido