Nexgrill 720-0888N Manual Del Usario página 14

PROBLEM
When attempting to light my grill, it
will not light immediately.
Rotisserie burner will not light when
the igniter button is pushed.
Regulator makes noise.
Full size cover does not fit the grill.
Rotisserie motor will not turn
Grill only heats to 200-300 degrees.
Grill takes a long time to preheat.
Burner flames are not light blue.
SOLUTION
Make sure you have a spark while you are trying to light the burner (if no Make sure you have a spark while you are trying to light the burner (if no
spark) . Check if the battery is installed properly. spark) . Check if the battery is installed properly.
Ensure that the wire is connected to the electrode assembly. Ensure that the wire is connected to the electrode assembly.
Clean wire (s) and / or electrode with rubbing alcohol and a clean swab. Clean wire (s) and / or electrode with rubbing alcohol and a clean swab.
Wipe with a clean cloth. Wipe with a clean cloth.
Check to see if the other burners operate. If so. Check the gas orifice on Check to see if the other burners operate. If so. Check the gas orifice on
the malfunctioning burner for an obstruction. the malfunctioning burner for an obstruction.
Check to see if debris is blocking the electrode. Check to see if debris is blocking the electrode.
Check to see if there is a spark that jumps to the burner from the Check to see if there is a spark that jumps to the burner from the
electrode. If no spark is seen, check the battery located inside the igniter electrode. If no spark is seen, check the battery located inside the igniter
box. To open turn counter box. To open turn counter
Does the infrared back burner light when attempting to light with a match ? Does the infrared back burner light when attempting to light with a match ?
If not, check to ensure the gas is on. If not, check to ensure the gas is on.
Vent hose on the regulator may be plugged or regulator may be faulty. Vent hose on the regulator may be plugged or regulator may be faulty.
Ensure the vent hole on the regulator is not obstructed. Clear the hole, Ensure the vent hole on the regulator is not obstructed. Clear the hole, Ensure the vent hole on the regulator is not obstructed. Clear the hole, Ensure the vent hole on the regulator is not obstructed. Clear the hole,
close the gas control valves. Wait ten minutes and re-start. close the gas control valves. Wait ten minutes and re
Check your flames for proper performance. If the flames are not correct, Check your flames for proper performance. If the flames are not correct,
replace regulator. replace regulator.
Cover may be incorrect for your grill. It may be a tight fit. Cover may be incorrect for your grill. It may be a tight fit.
Ensure the cover is the correct length for your grill. Ensure the cover is the correct length for your grill.
Measure it left to right. Compare to the grill's measurement. Measure it left to right. Compare to the grill's measurement.
Compare the location and size of the hood portion of the cover to your Compare the location and size of the hood portion of the cover to your
grill.
Spread the cover and allow it to relax, preferably in warm sunlight or in a Spread the cover and allow it to relax, preferably in warm sunlight or in a
warm room.
For grill with a side shelf bunch the cover like a sock, put on left to right. For grill with a side shelf bunch the cover like a sock, put on left to right.
Ensure the motor is connected to a properly grounded power supply. Ensure the motor is connected to a properly grounded power supply.
Ensure the on / off switch is in the on position. Ensure the on / off switch is in the on position.
Ensure that the spit is fully inserted into the rotisserie motor. Ensure that the spit is fully inserted into the rotisserie motor.
Ensure that the load does not exceed the 40 pounds operational capacity. Ensure that the load does not exceed the 40 pounds operational capacity.
Ensure that there is no encumbrance or drag. Ensure that there is no encumbrance or drag.
Check to see if the fuel hose is bent or kinked. Check to see if the fuel hose is bent or kinked.
Make sure the grill area is clear of dust. Make sure the grill area is clear of dust.
Make sure the burner and orifices are clean. Make sure the burner and orifices are clean. Make sure the burner and orifices are clean. Make sure the burner and orifices are clean.
Check for spiders and insects. Check for spiders and insects.
The regulator has a safety device that restricts the flow of gas in the event The regulator has a safety device that restricts the flow of gas in the event
of a leak. This safety device can be triggered without a gas leak. To of a leak. This safety device can be triggered without a gas leak. To
reset the safety device, turn off all burners and close the LP tank valve. reset the safety device, turn off all burners and close the LP tank valve.
Disconnect the regulator from the LP tank and wait one minute. Disconnect the regulator from the LP tank and wait one minute.
Reconnect the regulator to the LP tank and slowly open the LP tank Reconnect the regulator to the LP tank and slowly open the LP tank
valve until the valve is fully open. Light all burners and observe the valve until the valve is fully open. Light all burners and observe the
temperature.
Normal preheat 500-600 degrees, takes about 10-15 min. Cold weather Normal preheat 500
and wind may effect your preheat time. and wind may effect your preheat time.
If you are using volcanic rock or briquettes they can increase the preheat If you are using volcanic rock or briquettes they can increase the preheat
time and maximum temperature. time and maximum temperature.
Too much or not enough air for the flame. Too much or not enough air for the flame.
Elevation is the principal cause, however cold weather can affect the Elevation is the principal cause, however cold weather can affect the
mixture. Burner adjustment may be required. mixture. Burner adjustment may be required.
Grill is in a windy location. Grill is in a windy location.
14
Troubleshooting
continued