Master TERA Manual De Uso Y Mantenimiento página 16

15. OBSTACLE ON UPWARD
The motor is able to detect an obstacle during the upward movement. When the obstacle is detected, the motor stops
the maneuver and makes a short downward movement to don't keep the roller blind in traction.
It is possible to select the reactivity of the motor to the obstacle during the upward movement: the higher the value,
the greater the sensitivity.
The factory sets this parameter at level 3 (medium high sensitivity).
Use level 4 only if the sliding of the roller shutter is optimal.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 9 times NEXT.
«09» appears on display
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 4)
06. Press STOP. The motor signals the new
value (1 to 4 movements)
16. OBSTACLE ON DOWNWARD
Necessary condition for the proper operation of this feature is the use of the offset adapter, properly installed (see section
03 "Installation of offset adapters").
When the obstacle is detected, the motor stops the manoeuvre and makes a large upward movement to allow the
obstacle to be removed. The motor is able to detect obstacles such as to stop the roller shutter almost instantaneously,
obstacles that gradually slow down the rolling shutter may not be detected.
Setting 1: "Function inactive".
Choose this setting if the roller shutter does not slide well in the guides, to prevent the motor from detecting non-existent
obstacles. In this case, the factory also recommends checking the installation of the roller shutter.
Setting 2-4: "Minimum sensitivity - average - maximum".
Choose according to the desired reactivity. The factory sets the parameter at level 3 (average sensitivity). Use level 4
(maximum sensitivity) only if the sliding of the roller shutter is optimal.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 3 times NEXT.
«13» appears on display
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 4)
06. Press STOP. The motor signals the new
value (1 to 4 movements)
17. DISTANCE FROM MECHANICAL STOP
This function is available only if the upper limit switch has been learned by contact with a mechanical stop (using the
stoppers).
In this case, the motor will stop a few centimeters from the mechanical stop (only occasionally it will look for the stop to
automatically recalibrate the stroke). This parameter allows you to set the distance between the stop point and the
mechanical stop.
The factory sets the parameter at level 5.
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 8 times NEXT.
«08» appears on display
04. Press STOP. The motor signals the current
value (1 to 9 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 9)
06. Press STOP. The motor signals the new
value (1 to 9 movements)
Disposal
MASTER uses packaging recyclable materials. Dispose materials on the proper containers, complying with the law in force in your locality.
This product may have substances that are polluting for the environment and dangerous for the health.
At the end of the product life cycle, carefully comply with the waste disposal rules. It is strictly forbidden to dispose the product on the domestic waste.
All rights reserved. All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by the manufacturer, the device must be used
exclusively with transmitters produced by the same manufacturer. The manufacturer shall not be liable for damage resulting from improper, incorrect or unreasonable use.
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 9 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 4)
06. Press STOP. The motor signals the newt
value (1 to 4 movements)
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 1 time UP / 3 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 4)
06. Press STOP. The motor signals the newt
value (1 to 4 movements)
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 8 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 9 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 9)
06. Press STOP. The motor signals the newt
value (1 to 9 movements)
R
VISIO
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 9 times NEXT.
«09» appears on display
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press UP the number of times equal to the
desired setting (1 to 4)
06. Press STOP. The motor signals the new
value (1 to 4 movements)
*factory setting
VISIO
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 3 times NEXT.
«13» appears on display
04. Press STOP. The motor signals the current
value (1 to 4 movements)
05. Press UP the number of times equal to the
desired setting (1 to 4)
06. Press STOP. The motor signals the new
value (1 to 4 movements)
VISIO
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 8 times NEXT.
«08» appears on display
04. Press STOP. The motor signals the current
value (1 to 9 movements)
05. Press UP the number of times equal to the
desired setting (1 to 9)
06. Press STOP. The motor signals the new
value (1 to 9 movements)
08
N° of movements
1
2
Medium high
*
3
4
*factory setting
Other transmitters...
See the User manual of
the transmitter at
«RECEIVER MENU -
Function 09»
N° of movements
Not active function
1
Minimum sensitivity
2
*
Medium sensitivity
3
Maximum sensitivity
4
Other transmitters...
See the User manual of
the transmitter at
«RECEIVER MENU -
Function 13 -
Obstacle on downward»
N° of movements
Minimum distance
1
*
2 - 3 - 4 - 5 - 6 - 7- 8 Intermediate distances
9 Maximum distance
*
factory setting
Other transmitters...
See the User manual of
the transmitter at
«RECEIVER MENU -
Function 08»
Sensibility
Minimum
Medium
Maximum
section:
Setting
section:
Setting
section: