Uline H-3530 Manual De Instrucciones página 4

REPLACEMENT PARTS
• Bostitch replacement parts are recommended. Do
not use modified parts or parts which will not give
equivalent performance to the original equipment.
ASSEMBLY PROCEDURE FOR SEALS
• When repairing a stapler, make sure the internal
parts are clean and lubricated. Use Parker O-LUBE
or equivalent on all O-Rings. Coat each O-Ring
with O-Lube before assembling. Use a small amount
of oil on all moving surfaces and pivots. After
reassemble add a few drops of Bostitch Air Tool
Lubricant through the air line fitting before sealing.
STAPLER SPECIFICATIONS
ULINE PART NO.
H-3530
FASTENER SPECIFICATIONS
ULINE PART NO.
S-2724
S-2725
PARTS/STAPLE CHART
CLINCHERS
A01900601(L.H.)
SPACERS
STAPLE LENGTHS
DIAL POSITION
STAPLER AIR FITTING
This stapler must use a male free-flow connector plug,
1/4" N.P.T. The minimum inside diameter should be .300"
(8mm). Fitting must be capable of discharging stapler
air pressure when disconnected from the air supply.
OPERATING PRESSURE
The operating pressure of the stapler is 70 to 100 psi
(5 to 7 kg/cm ). Select the operating pressure within this
2
range for best fastener performance.
PAGE 4 OF 15
MFG. PART NO. LENGTH
D62ADC 9" (228mm)
LEG LENGTH STAPLE SERIES
5/8" (16mm)
3/4" (19mm)
Standard/Flat
A01900501(R.H.)
A02300801 A02300801
5/8" (16mm) 3/4" (19mm)
MAINTENANCE
AIR SUPPLY - PRESSURE AND VOLUME
• Air volume is as important as air pressure. The air
volume supplied to the stapler may be inadequate
due to undersized fittings and hoses or from the
effects of dirt and water in the system. Restricted
air flow will prevent the stapler from receiving an
adequate volume of air even though the pressure
reading is high. The result will be slow operation,
misfeeds or reduced driving power. Before
evaluating stapler problems for these symptoms,
trace the air supply from the stapler to the supply
source for restrictive connectors, swivel fittings, low
points containing water or anything else that would
prevent full volume flow of air to the stapler.
SPECIFICATIONS
HEIGHT
8.625" (219mm)
WIRE SIZE
.074 x 0.37"
SWC
(1.88 x 94mm)
.074 x 0.37"
SWC
(1.88 x 94mm)
D60065(R.H.)
175497
1/2" (13mm)
AIR CONSUMPTION
Model H-3530 requires 4.0 cubic feet per minute (.113
cubic meters) of free air to operate at the rate of 100
fasteners per minute, at 80 psi (5.66kg/cm
actual rate at which the stapler will be run to determine
the amount of air required. For instance, if your fastener
usage averages 50 fasteners per minute, you need
50% of the stapler's cfm of free air which is required for
running at 100 fasteners per minute.
WIDTH
4.5" (115mm) 5.9 lbs. (2.5 kg)
CROWN WIDTH FASTENER RANGE
1-3/8"
(35mm)
1-3/8"
(35mm)
Shallow/Flat
D60066(L.H.)
175497
5/8" (16mm)
CAUTION: Do not exceed the recommended
operating pressure.
ROLL
WEIGHT
CAPACITY
1,000
1/2" - 3/4"
(12-19mm)
1/2" - 3/4"
(12-19mm)
). Take the
2
0421 IH-3530