Troubleshooting - Cooper Lighting HALO FSL503TB Instrucciones

FIXTURE BOXES
1. Line up the holes on the mounting bracket (B) with
the holes on your junction box. Using either (2) #6
screws or (2) #8 screws (D) (depending on size of
the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 5).
2. Thread fixture wires through mounting bracket (B)
(Fig. 5).
3. Hang one end of the support hook (F) onto the
mounting bracket guide tabs and hang the light
fixture on the other end of the support hook (Fig. 6).
4. Thread fixture wires through the gasket (C) and
connect fixture black wire to house black wire,
fixture white wire to house white wire, and fixture
ground wire to house ground wire using the
attached quick connectors (Fig.8).
5. Remove support hook (F) and attach fixture (A) to
the mounting bracket (B) using (2) #8 x 1-1/4 in.
screws (D) provided. Be sure no loose wires remain
sticking out from underneath the coverplate. Insert
the decorative screw cover caps (H) into the screw
holes on the coverplate for a finished appearance
(Fig. 7).
6. Apply silicone caulk around the edges of the
coverplate to provide a watertight seal from
rain and moisture.
7. Turn on power at main fuse/breaker box.
8
A
WALL AND EAVE SURFACE MOUNT FIXTURE BOXES
PART 1: ATTACHING ADAPTER PLATE TO FIXTURE BOX
For use with 4" round fixture box
1. Determine the proper orientation of the adapter
plate based on your fixture box location. You may
need to drill out the alternate mounting holes to
properly mount the adapter plate to your fixture box
using a 7/32" drill bit.
2. Peel off the adhesive side of gasket (E) and place on
the bottom of the adapter plate (A), making sure to
line up the holes in the gasket with the plate (Fig. 1).
3. Route supply wires through center hole of adapter
plate (A).
4. Place two screws (C) or (D) through two holes
in adapter plate (A) and align with fixture box (not
included). Tighten down both screws (Fig. 2).
5. Apply silicone caulk around the edges of the fixture
box and adapter plate.
4
1-1/2 in. 1-1/2 in.
Round Octagonal
5
Junction box
B
D
D
6
7
G
F
A
B
C
Junction
box
Fig. 1
E
Fig. 2
D
C
PART 2: ATTACHING FLOOD LIGHT FIXTURE TO ADAPTER PLATE
6. Peel off the adhesive side of the gasket included
with the fixture and place on top of the adapter
plate (A) (Fig. 3).
7. Make all electrical connections using wire nuts
included with the fixture. Refer to fixture instruction
sheet for detailed wiring instructions.
NOTE: Ensure that all ground wires are attached.
8. Line up the holes on the fixture's coverplate with
the holes on the adapter plate (A). Attach fixture
to the adapter plate (A) using the two #8-32 x 1-¼"
screws included with the fixture (Fig. 4).
9. Insert decorative screw cover caps (included with
the fixture) into the coverplate holes for a finished
appearance.
10. Apply silicone caulk to provide a watertight seal
from rain and moisture.
E

TROUBLESHOOTING

Problem Cause / Solution
Light does not No power to the fixture.
come ON.
G
TURN OFF POWER BEFORE CONTINUING
Wiring to the unit is loose.
F
Light flashes Make sure fixture is not on the same circuit as any dimmer,
or ceiling fan
5-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting Solutions ("CLS") warrants to customers that, for a period of five years from
the date of purchase, CLS products will be free from defects in materials and workmanship.
The obligation of CLS under this warranty is expressly limited to the provision of replacement
products. This warranty is extended only to the original purchaser of the product. A
purchaser's receipt or other proof of date of original purchase acceptable to CLS. This is
required before warranty performance shall be rendered. This warranty does not apply to CLS
products that have been altered or repaired that have been subjected to neglect, abuse,
misuse or accident (including shipping damages). This warranty does not apply to products
not manufactured by CLS which have been supplied, installed, and/or used in conjunction with
CLS products. Damage to the product caused by replacement bulbs or corrosion or
discoloration of brass components are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT
LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE
A
LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE
TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR
MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE,
EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR
CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.
To obtain warranty service, please contact CLS, at 1-800-334-6871, press option 2 for
Customer Service, or via e-mail [email protected] and include the
following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
A
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused. CLS is not responsible for
merchandise damaged in transit. Repaired or replaced products shall be subject to the terms
of this warranty and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a claim filed with
them.
Reproductions of this document without prior written approval of CLS are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected]
Printed in China
2
• Check if circuit breaker tripped.
• Confirm wall switch is ON.
• Confirm wiring is properly secured.
* If light still does not come on after checking wiring
connections, contact Customer Service.
Fig. 3
Fig. 4