Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PI100ASB_ManualEN_052507.qxp
100 watts. If the power consumption is rated in amps AC, simply multiply by the AC volts (115) to determine
the wattage.
Resistive loads are the easiest for the inverter to run; however, it will not run larger resistive loads (such as
electric stoves and heaters), which require far more wattage than the inverter can deliver. Inductive loads (such
as TVs and stereos) require more current to operate than do resistive loads of the same wattage rating.
For safety reasons, the unit will simply shut down if it is overloaded. To restart the unit, simply unplug all
devices plugged into the unit; disconnect the unit from any 12 volt DC power source; then reconnect the unit
BEFORE plugging the appliance back in.
Operation of the 115 Volt AC Outlet
1. Connect the Power Cord to the inverter.
2. Connect either the 12 Volt DC Vehicle Accessory Adapter or the 12 Volt DC Airplane Adapter to the end of the
12 Volt Power Cord.
3. Insert the selected Adapter Plug into a vehicle's accessory outlet or other 12 volt DC power source. Make sure
there is adequate space for proper ventilation of the inverter.
4. Rotate the vehicle accessory plug slightly to make sure there is good contact.
5. The Bi-color Power/Fault LED Indicator will light blue, indicating a proper connection.
6. If the Inverter does not work, make sure the ignition/accessory switch is actually powering the accessory
outlet. Some vehicles require the ignition switch to be turned on.
7. Plug the (110/120 volt AC) appliance into the Inverter's three-prong AC outlet and operate normally.
Notes: The Inverter will not operate appliances and equipment that generate heat, such as hair dryers, electric
blankets, microwave ovens and toasters.
Remember to disconnect the unit from any power source when it is not in use.
Operation of the USB Charging Port
1. Connect the Power Cord to the inverter.
2. Connect either the 12 Volt DC Vehicle Accessory Adapter or the 12 Volt DC Airplane Adapter to the end of the
12 Volt Power Cord.
3. Insert the selected Adapter Plug into a vehicle's accessory outlet or other 12 volt DC power source. Make sure
there is adequate space for proper ventilation of the inverter.
4. Rotate the vehicle accessory plug slightly to make sure there is good contact.
5. The Bi-color Power/Fault LED Indicator will light blue, indicating a proper connection.
6. If the Inverter does not work, make sure the ignition/accessory switch is actually powering the accessory
outlet. Some vehicles require the ignition switch to be turned on.
7. Plug the USB-powered device into the inverter's USB Charging Port and operate normally.
Notes: This inverter's USB Charging Port does not support data communication. It only provides 5 volts/300mA DC
power to an external USB-powered device.
Remember to disconnect the unit from any power source when it is not in use.
Protective Features
The inverter monitors the following conditions:
Low Battery Voltage — This condition is not harmful to the inverter, but could damage the power source,
so the inverter will automatically shut down when input voltage drops below 10.0 ± 0.3 volts DC.
Input Voltage Too High — The inverter will automatically shut down when DC input voltage exceeds 15.5 ± 0.5
volts, as this can harm the unit.
Thermal Shutdown Protection — The inverter will automatically shut down when the unit becomes overheated.
Overload/Short Circuit Protection — The inverter will automatically shut down when a short circuit occurs.
Notes: The Power/Fault LED Indicator will light red to indicate a Fault condition before automatic shutdown occurs.
If unit shuts down, disconnect it from the 12 volt DC power source, remove the load, wait a few minutes,
then plug it back in.
Operating Tips
The inverter should only be operated in locations that are:
DRY — Do not allow water or other liquids to come into contact with the inverter.
5/25/2007
12:22 PM
Page 5
5
Tabla de contenido
