Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Removing Paint (Fig. A)
WARNING: Refer to Important Notice under
Additional safety information before using the
tool to remove paint.
WARNING: Do not strip metal window frames as the
heat may crack the glass.
•
When striping other window frames, use a glass
protection nozzle.
•
To prevent igniting the surface, do not keep the
tool directed at one spot too long.
•
Avoid collecting paint on the scraper accessory, as
it may ignite. If necessary, carefully remove paint
debris from the scraper accessory using a knife.
1. Attach the appropriate accessory.
2. To power on the tool, flip lock-off
depress the trigger
.
1
3. Direct the hot air onto the paint to be removed.
Best results will be achieved if the heat gun is moved
slowly, but CONSTANTLY, from side to side to evenly
distribute heat. DO NOT LINGER OR PAUSE IN ONE SPOT.
4. When the paint softens, scrape the paint away using a
hand scraper.
REMEMBER: Splinters and small particles of stripped paint
can be ignited and blown through holes and cracks in the
surface being stripped.
Cool Down Period (Fig. E)
The nozzle and accessory becomes very hot during use.
Turn heat gun off, disconnect from the power source, place
in position shown in Fig. E, and let the tool cool down for at
least 30 minutes before moving or storing it.
Fig. E
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning
Accessories
7
upwards and
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN1-888-331-4569.
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
Register Online
Thank you for your purchase. Register your product now for:
•
•
•
•
Three Year Limited Warranty
CRAFTSMAN will repair or replace, without charge, any
defects due to faulty materials or workmanship for three
years from the date of purchase (two years for batteries).
This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage
and warranty repair information, visit www.craftsman.com
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with this product.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a CRAFTSMAN
factory service center or a CRAFTSMAN authorized
service center. Always use identical replacement parts.
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.craftsman.com/
English
9
Tabla de contenido
