Lock Installation (En); Technical Characteristics - ISEO Thesis 2.0 Manual Del Usuario

T he si s 2.0
Professional Mini

LOCK INSTALLATION (EN)

w w w. i s e o . c o m
Non contractual document. Subject to change. Cod. 6000780P002.1, Rev. 001 - 16/07/2021
Thesis 2.0 Professional Mini Installation Guide (EN) - © 2021 Iseo Serrature S.p.a. - www.iseo.com
1. WARNINGS
Failure to comply with the instructions laid out in this manual will affect the proper functioning of the lock,
with consequent loss of warranty.
This product can only be used for what it was specifically designed to do. Any other use is considered
irregular and dangerous.
Provisions should be made to ensure that a suitable isolation and protection switch be placed upstream
of the power supply.
Do not use the lock as a drilling template.
Do not paint or lubricate the lock.
Always ensure the bolt is clean and free of friction. In case the valve needs to be cleaned, do not use
products that can leak into the lock.
We recommend you equip the door with a door closer to prevent rebound when closing the door.
If there is no power supply, the NC version of the solenoid lock can only be opened mechanically through
the cylinder or the handle (where applicable). On the other hand, the NA version of the solenoid lock
cannot be mechanically closed if there is no power supply.
ISEO srl. is not required to comply with warranty conditions if the product has been subjected to changes,
repairs or alterations by unauthorized personnel.
For manufacturing and commercial reasons, or to improve the quality of its product, ISEO srl reserves the
right to make any changes it deems appropriate to the product and its instruction manual without prior notice.

2.2 TECHNICAL CHARACTERISTICS

Opening time: programmable from 1 to 180
seconds (default: 15 seconds).
Locking time at closing of the door: programmable
from 1 to 60 seconds (default: 1 second).
Temperature range of operation: -20°C to +60°C
(-4°F to 140°F).
Storage temperature: -25°C to +70°C (-13°F to 158°F).
Protection system (IP grade) IP44.
4. DIMENSIONS AND INSTALLATION OF THE STRIKING PLATE
4
Iseo Serrature s.p.a
®
Via San Girolamo 13
25055 Pisogne (BS)
ITALY
Tel. +39 0364 8821
[email protected]
ELECTRONIC SUPPORT SERVICE
iseo.com
Reference standards: EN 14846:2008
Classification: 3 H 8 0 0 M 7 0 1.
Packaging dimensions: width 38.5 cm - depth 10
cm - height 4 cm.
Package weight: 1.4 kg.
Package contents: lock, striking plate, multilingual
instruction booklet (IT/GB/FR/DE/ES), screws,
connector with rubber protection, 8mm handle
bracket (if envisioned).
NOTE
Correctly secure
striking plate so that
once the installation is
complete and the door
is closed, the bolt does
not scrape against the
striking plate itself.
Failure to use
door's alignment
sphere (supplied) will
compromise the correct
functioning of the lock.
Distance between
striking plate and lock:
min 4mm - max 9mm
INDEX
WARNINGS
TECHNICAL CHARACTERISTICS
DIMENSIONS AND LOCK INSTALLATION
LOCK AND CYLINDER INSTALLATION
DIMENSIONS AND INSTALLATION OF THE STRIKING PLATE
STRIKING PLATE ADJUSTMENTS
2.1 TECHNICAL CHARACTERISTICS
Available in version NC (normally closed) and NO
(normally open) in the absence of a power supply.
Available with activation software for single door,
for bidirectional manual interlocking, and for
bidirectional automatic
communication between the interlocking locks is
encrypted).
DC Voltage power supply: 8 to 30 VDC.
Maximum supply current during operation: 1A.
3. LOCK DIMENSIONS AND INSTALLATION
4
CAUTION
Take care to avoid
damaging the cable
during installation.
22
5. STRIKING PLATE ADJUSTMENTS
the
1
the
EC Declarations of conformity available at:
https://www.iseo.com/it/en/download
Minimum supply current: 8 to 30 VDC, 15W.
"LOCKBUS" communication channel: multi-point
serial interface (3 wires: power/data).
interlocking (the
Opening control: optically isolated input 8 to 24
VDC/12 VAC.
Signal relays: voltage and maximum applicable
current 24 VDC 1A/120 VAC, 0.5A.
30
44
27
ø
18
Adjust the "door positioning" sensor
maximum distance of 5 mm from the front of
the lock. Distances greater than this will
compromise the correct functioning of the
lock in the automatic closing phase of the
bolt.
Adjust the protrusion of the door
2
alignment sphere working a screwdriver in
a clockwise or counter-clockwise direction.
Adjust the thrust force of the sphere (3). To
this end, insert a small screwdriver into
the sphere's opening until you reach the
3
screw placed on the brass cap. Turn
counter-clockwise to increase the pressure
of the thrust, or in a clockwise direction to
diminish it.
NOTE
2/3
Be careful not to excessively turn the
screwdriver clockwise (3), as you may run the
risk of unscrewing the rear cap, which holds
the spring in place, inserted in the group.
1
2
3
4
5
6
(1) to a
(2)