Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS
Sear". Press "Time" once, and
then press "+" until "00:05" is
reached. Press "Med/Low".
Press "Time" twice, and then
press "+" until "00:20" is
reached. Finally, press "Start".
NOTE: Maximum
programmable cook time is
99 hours and 60 minutes.
Delay Function:
The purpose of this function
is to allow for set programs
to start at a later time.
1.
To delay a program,
press "Prog".
2.
Press "Time". A "0" will
flash in the display panel.
3.
Press "+" until the desired
amount of time to delay
the program start is
reached. See "Setting
Cooking Time" for more.
Panel Display Chart
Press Button
Temperature
Low
100°F / 38°C
Med/Low
175°F / 79°C
Med
275°F / 135°C
Med/High
375°F / 191°C
High
425°F / 218°C
Max/Sear
575°F / 302°C
The minimum is 100F (38C) while the maximum temperature
reaches 500F (260C).
Note: Do not remove pots and pans during cooking process. If
necessary, press "Pause/Clear" to pause before removing.
12
12
instructions
4.
Press "Prog" again to set
cooking program. The
amount of time selected
for delay is included in the
programmed stages.
To continue to the
•
next stage, enter the
cooking temperature.
Continue with step "2."
from the "Programming
Function" instructions.
Once ready for the
5.
countdown to begin,
press "Start". When delay
countdown reaches "0",
the PIC Gold will beep
twice to signal the end.
At this point, the cooking
time will start and the
temperature will be
displayed.
Panel Display
Examples
100F / 38C
Warm
175F / 79C
Simmer
275F / 135C
Steam
375F / 191C
Stir/Deep-Fry
425F / 218C
Boil/Saute
SEAR
Sear
TROUBLESHOOT GUIDE
Error Message:
An E1 reading typically means the PIC Gold
does not detect cookware on its surface. This
can occur for one of two reasons:
1.
The induction coils contained within the
PIC Gold will only work when they are in
direct contact with a piece of cookware. To
E1
maintain your appliance's effectiveness,
always ensure that it rests on a flat surface
and that contact is consistent with your
cookware.
2.
An E1 message may also occur if the
chosen cookware is not induction-ready.
The PIC is malfunctioning.
E2
Contact Customer Service.
The PIC's voltage is too low.
E3
Minimum = 85 volts
The PIC's voltage is too high.
E4
Maximum = 144 volts
The PIC is malfunctioning.
E5
Contact Customer Service.
The PIC is malfunctioning.
E6
Contact Customer Service.
Overheating, or air ventilation is obstructed.
If internal temperature exceeds 230F (110C),
E7
operation will cease, and the PIC will beep. Press
Pause/Clear twice. Wait for the PIC to cool.
Overheating, if PIC exceeds a temperature 20F
E8
(-7C) higher than sear, the appliance will turn
off. Contact Customer Service.
The PIC is malfunctioning.
E9
Contact Customer Service.
In programming mode, when the total entered
FULL
time reaches the appliance's limit of 99:60, no
additional stages can be inputted.
• When any of the above error messages are displayed on the LED,
the PIC will beep at least once.
• The fan will run up to a maximum of 60 seconds after pressing
"Pause/Clear" once. Continue cooking by pressing "Start" within
45 minutes.
Solution(s):
13
13
nuwavenow.com
nuwavenow.com
Tabla de contenido
