Join the support plate (A) to the crossbeam using galvanised metal wire of at least 2.5mm in diameter.
Passing the wire through the grooves in the plate, wind it around the crossbeam and back through
the plate a minimum of six times, so that at least some of the turns pass through the groove in the
crossbeam. Secure the wire by twisting it around itself several times.
Ensure that the ceiling is able to support the weight of the fan when in operation (minimum 25/40
Kg.). (Fig.3)
Fitting to a wooden beam
Fitting to a wooden beam
Four screws (H) are supplied together with safety washer's (I) for fitting the support plate (A) to a
Four screws (H) are supplied together with safety washer's (I) for fitting the support plate (A) to a
wooden beam. The holes for the screws should not be of greater diameter than the diameter of the
wooden beam. The holes for the screws should not be of greater diameter than the diameter of the
screw. Ensure that the wooden beam is able to support the weight of the moving fan (minimum
screw. Ensure that the wooden beam is able to support the weight of the moving fan (minimum
25/40 Kg.) (Fig.4)
25/40 Kg.) (Fig.4)
ASSEMBLY OF THE FAN
ASSEMBLY OF THE FAN
IMPORTANT: If you installing more than one fan, ensure that you do not mix the fan blade sets, even
IMPORTANT: If you installing more than one fan, ensure that you do not mix the fan blade sets, even
though they are from the same ceiling fan model.
though they are from the same ceiling fan model.
1. Fit the blades (C) to the motor assembly and support (B) using the blade fitting screws (D) and the
1.- Fit the blades with the angles as shown in figure 5
1.- Fit the blades with the angles as shown in figure 5
safety washers (E). Do not forget to use the felt protection washers (J) between the blade and the
motor assembly to avoid possible noise. Repeat this process with the remaining blades. (Fig.5)
2.- Fit the blades (C) to the motor assembly and support (B) using the screws (D) and the safety
2.- Fit the blades (C) to the motor assembly and support (B) using the screws (D) and the safety
washers (E). Do not forget to use the felt protection washers between the blade and the motor
washers (E). Do not forget to use the felt protection washers between the blade and the motor
IMPORTANT: Be careful not to support yourself on the fan blades, as these could then become
assembly to avoid possible noise. Repeat this process with the remaining blades. (Fig.6)
assembly to avoid possible noise. Repeat this process with the remaining blades. (Fig.6)
unbalanced and cause vibration or shaking of the fan.
IMPORTANT: Be careful not to support yourself on the fan blades, as these could then become
IMPORTANT: Be careful not to support yourself on the fan blades, as these could then become
2. Loosen the screws situated in the base of the decorative canopy to allow easier access to the
unbalanced and cause vibration or shaking of the fan.
unbalanced and cause vibration or shaking of the fan.
anchorage point and electrical connectors. Hang the motor and support assembly (B) from the
hook on the support plate (A) (previously fixed to the ceiling) (Fig.6)
3.- Loosen the screws situated in the base of the decorative canopy to allow easier access to the
3.- Loosen the screws situated in the base of the decorative canopy to allow easier access to the
anchorage point and electrical connectors. Hang the motor and support assembly (B) from the hook
anchorage point and electrical connectors. Hang the motor and support assembly (B) from the hook
3. Connect the cables and position them correctly. The connections and the fitting point can be
on the support plate (A) (previously fixed to the ceiling) (Fig.7)
on the support plate (A) (previously fixed to the ceiling) (Fig.7)
hidden using the decorative canopy. Fix the two screws situated in the base of the decorative
canopy.
4.- Connect the cables and position them correctly. The connections and the fitting point can be
4.- Connect the cables and position them correctly. The connections and the fitting point can be
hidden using the decorative canopy.
hidden using the decorative canopy.
INSTALLATION ELECTRICAL
INSTALLATION ELECTRICAL
IMPORTANT SAFETY NOTICE: Before installation, ensure that the electrical supply is disconnected
IMPORTANT SAFETY NOTICE: Before installation, ensure that the electrical supply is disconnected
at the mains junction / fuse box.
at the mains junction / fuse box.
- The airflow direction can be changed depending upon the wiring connection configuration in
- The airflow direction can be changed depending upon the wiring connection configuration in
- The wiring connection to connect the speed regulator supplied with the fan, is indicated in the
- All products are supplied, factory wired, for a downward airflow configuration.
Figure 7.
- All products are supplied, factory wired, for a downward airflow configuration.
- If the airflow direction is required to be changed on a frequent basis, then an airflow direction
- With the switch can be change airflow direction (Fig.8).
- If the airflow direction is required to be changed on a frequent basis, then an airflow direction
switch should be installed as a separate additional accessory (Fig.9)
switch should be installed as a separate additional accessory (Fig.9)
IMPORTANT: Before changing the direction of ariflow, the fan blades must have completely stopped
IMPORTANT: Before changing the direction of ariflow, the fan blades must have completely stopped
turning after switching the unit to the off position.
IMPORTANT: Before changing the direction of ariflow, the fan blades must have completely stopped
turning after switching the unit to the off position.
turning after switching the unit to the off position.
OPERATION INSTRUCTIONS
OPERATION INSTRUCTIONS
1. – The speed regulator has four positions.
1. – The speed regulator has four positions.
0 .........OFF
0 .........OFF
1 ......... High speed
1 ......... High speed
2 ......... Medium speed
10
accordance with (Fig.8)
accordance with (Fig.8)
13