General Power Tool Safety Warnings - REMS MSG 25 EE Instrucciones De Servicio

g
Translation of the Original Instruction Manual
EE
1 Supporting stand
2 Bench support
3 Handle
4 Heating element
5 Welding tools (hea ing spigot + socket)
6 Red power-on indicator lamp
7 Green temperat. indicator lamp
8 Temperature adjusting screw
Fig. 4
(1) Preparations
(2) Heating element
(3) Sleeve
(4) Heating spigot
(5) Heating socket
(6) Pipe
(7) Heating
(8) Completed joint
Fig. 5
(1) Pipe outer diameter d

General Power Tool Safety Warnings

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
Save all warnings and instructions for future reference.
The term "power tool" used in the safety notes refers to mains operated power tools
(with power cable).
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distrac-
tions can cause you to lose control.
2) Electrical safety
Do not use any adapter plugs with earthed (grounded) power tools. Unmod-
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
electric shock.
3) Personal safety
power tools may result in serious personal injury.
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec-
tion used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source, picking up or carrying the tool. Carrying power
on invites accidents.
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
hair can be caught in moving parts.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
FM
1 Supporting stand
2 Bench support
3 Handle
4 Heating element
5 Welding tools (heating spigot + socket)
6 Green power-on indicator lamp
7 Red temperature indicator lamp
(2) Heat up
Heating element temperature
250 – 270°C
Heat-up time for SDR
(3) Switchover
Switchover time (maximum time)
(4/5) Cool down
Cool down time total min
SDR = Standard Dimension Ratio ~
1)
d/s. (ratio outer diameter/wall thickness)
Power tools create sparks which
Damaged or knotted cables
Use of an RCD reduces the risk of
A moment of inattention while operating
Protective
This enables
Loose clothes, jewellery or long
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
changing accessories, or storing power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
tool. Power tools are dangerous in the hands of untrained users.
accidents are caused by poorly maintained power tools.
f) Use power tools, accessories and insert tools etc. according to these
consideration. The use of power tools for purposes for which they are not
intended can lead to dangerous situations.
safe handling and control of the power tool in unexpected situations.
5) Service
is maintained.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
Save all warnings and instructions for future reference.
Only connect the electrical device to an outlet with protected earth.
Only touch the electrical device on the handle (3) when it is plugged into
an outlet. The heating element (4), the heating tools (5) as well as the metal
parts between the heating element and the plastic handle (3) reach operating
temperatures of up to 300°C. Touching these parts can cause severe burns.
-
phase can cause severe burns. The electrical device takes a long time to cool
down after unplugging.
suitable gloves when welding. The pipes and mouldings to be welded, the
heating element and the heating tools get hot during welding and can cause
severe burns. The weld connection stays very hot for a long time after comple-
tion.
Touching parts which are still hot causes severe burns.
tions. Touching the hot parts causes severe burns.
it in liquid. There is a danger of injury from electric shock and/or sudden spurting
of the liquid. The electrical device will also be damaged.
Place the electrical device down only on its supporting stand (1), in the
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
REMS customer service workshop in case of damage.
-
or lack of experience and knowledge are unable to operate the electrical
instruction by a responsible person. Otherwise there is a risk of operating
errors and injuries.
WARNING Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
A
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
Read the operating manual before starting
Power tool complies with protection class I
Environmentally friendly disposal
CE conformity mark
Slippery handles prevent
This will ensure that the safety of the power tool
There is a danger of accident.
Touching parts that are still hot during the cooling
Placing the hot electrical device
g
Many
-
-