Setting The Alarm - THOMSON CR50DAB Instrucciones De Funcionamiento

• 12/24 hour clock display
• The date format, DD-MM-YYYY or MM-DD-YYYY
• To auto update the time from the DAB signal, FM signal, DAB or FM signal or no update.

Setting the alarm

Note: Check that the radio has the correct time and date before you set an alarm.
With your radio switched on (Not in standby mode)
1) Press and hold the MENU/INFO button until the menu is shown.
2) Use the TUNING+/TUNING- button to scroll to '<System>'. Press the SELECT button to select.
3) Use the TUNING+/TUNING- button to scroll to '<ALARM>'. Press the SELECT button to select.
4) Use the TUNING+/TUNING- button to scroll to scroll to <Alarm 1> or <Alarm 2> as required. Press
and release the SELECT button. The hour digits for the alarm will flash.
5) Use the TUNING+/TUNING- button to adjust and press the SELECT button to confirm.
6) The minutes will now flash. Use the TUNING+/TUNING- button to adjust and press the SELECT
button to confirm.
7) Use the TUNING+/TUNING- button to scroll to choose the alarm duration, from 15, 30, 45, 60, 90
and 120 minutes. Press and release the SELECT button.
8) Press the TUNING+/TUNING- button to scroll to the sound source for the alarm. You can choose
from Buzzer, DAB or FM. Press and release the SELECT button.
Note: If you select DAB or FM radio for the alarm source, 'Last' will flash on the display. Press
the TUNING+/TUNIING- button to select, and the last radio station listened to in DAB or FM, as
appropriate, will be used for your alarm.
9) Use the TUNING+/TUNING- button to scroll to the frequency for the alarm. You can choose from
Daily, Once, Weekends or Weekdays. Press and release the SELECT button.
10) Use the TUNING+/TUNING- button to scroll to the volume for the alarm. Press and release the
SELECT button.
11) Use the TUNING+/TUNING- button to scroll to ON. Press and release the SELECT button. The
display will confirm 'SAVE'.
Note: If you select "Once", you will then be prompted to set the date for your alarm.
Note: An alarm symbol at the bottom of the radio display together with the digit "1" or "2" will
confirm that an alarm has been set.
Note: If the time is not set or has failed to update from the radio signal, <Time is not set> will
be displayed when you try to set the alarm. The radio will then prompt you to set the time. An
alarm can only be set after the time has been set.
Stop the Alarm
When the alarm sounds, press and release the STANDBY/MODE button, Alternatively, you can press
and release the Snooze/Sleep button (see Snooze function below).
Note: If you press the STANDBY/MODE button to stop the alarm, the alarm symbol will remain on the
display and the alarm will sound again at the same time the next day, unless it was set for "Once".
Snooze function
If you want to snooze for a few more minutes when an alarm sounds, press the SNOOZE BUTTON
while the alarm is sounding. The alarm will sound again after 10 minutes. Press the STANDBY/MODE
button to turn the Snooze function off.
Sleep timer
You can set your radio to turn off automatically using the sleep timer. You can choose from Sleep, Off,
15, 30, 45, 60 and 90 minutes.
In DAB or FM mode:
press and release the SNOOZE/SLEEP button repeatedly to cycle through the different sleep timer
options such as Sleep, Off 15, 30, 45, 60 and 90 minutes. Then press the SELECT button to confirm.
Note: To cancel the sleep timer, follow the steps to set the sleep time but stop when 'OFF' is displayed
then press the SELECT button to confirm.
- EN 7 -